Onboard LM386 Chip.
200 multiplier benefits circuit design.
On-board speaker wiring Block.
On-board 10K variable resistor, you can adjust the volume of the enlarged.
Onboard Power Indicator.
Accuracy 2 ppm from 0° C to +40° C
Accuracy 3.5 ppm from -40° C to +85° C
Digital Temp Sensor Output: ±3° C Accuracy
Memory Chips: AT24C02 (2Kbit)
Register for Aging Trim
RST Output/Pushbutton Reset Debounce Input
Two Time-of-Day Alarms
Programmable Square-Wave Output Signal
Fast 400 Khz I2C interface
QUICK OVERVIEW
Channel: 1 channel
Relay Voltage: 5V
High impedance controller pin
Pull-down circuit for the avoidance of malfunction
One normally closed contact and one normally open contact
Triode drive, increasing relay coil
Bluetooth version: 4.2
Supply current: 1A
Power supply voltage: 5V
Max. Audio Output Power: 10W
No soldering Required on Module
QUICK OVERVIEW:
QUICK OVERVIEW:
QUICK OVERVIEW
Built-in Industrial Micro-Controller
Big LCD Display
All Adjustable Parameters
Full 4 Stage PWM Charge Management
Compatible Chips:
ATMEGA Series
Tiny Series
Classic Series
CAN Series
PWM Series
Operating Voltage: 3.7 – 5VDC
SNR: 90dB
Support Profile: A2DP / AVCTP / AVDTP / AVRCP / HFP
Brand new and high quality
Included USB transceiver, without external circuit device
With 3.3V and 5V dual power output
With three LEDs: power indicator, data reception indicator, the data transmission indicator, working status
Meets the USB2.0 specification requirements
With self-recovery fuse. In the event of the accidental short circuit, it can effectively protect your computer USB port and Downloader
Asynchronous serial data bus compatible with all handshake and modulation controller interface signals
The supported data format is 8 data bits, 1 stop bit and parity bits
Operating Voltage: AC 220V
Maximum Power: 5000W
Voltage range (adjust temperature or light): 0-220V AC
High-temperature FR-4 PCB
100% High quality and Brand new
Terminal RS485 interface
Support 32 slave devices
Baud rate support 300~115200bps
Support MQTT gateway function.
Operating temperature -40~85℃
Supply voltage(V):+3.3 to +5.5
operating temperature range:-40°C to +85°C
Supported Raspberry Pi and Arduino
Provide battery backup for continuous timing.
Two calendar alarm.
1Hz and 32.768kHz output.
Quick Overview
Operating Voltage: 12V DC
Two separate LEDs for On/Off indication of the Relay
Triggering input voltage 3.3V – 5V 4)
Back EMF protection
Equipped with high-current relay 10A@250VAC / 10A@30VDC
It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
Freewheeling diode to protect your microcontroller
Input Signal Pin connected to Burg stick for easy accessibility
Mounting holes provided
QUICK OVERVIEW:
FEATURES:
Type: LM2596 DC Power Supply Step-down Module
– Input: 5-60V
– Output: 1.25-26V
– Output max current: 3A
– Continuous operating current: 1.2A (output power within 20W)
QUICK OVERVIEW
16 Bit Bidirectional I/O Port.
Configurable Interrupt Output Pins
Configurable Interrupt Source.
High-Speed I2C Bus Compatible.
External Reset Input.
Low Standby Current
Operating voltage: DC 5V
Operating temperature: -40~80 degrees
Operating frequency: 433MHZ Receive sensitivity: ≥-95dB
Working Mode: jump switch, point action, self-locking, and interlocking(adjustable)
On orders above ₹999
Min. order ₹250 for COD
Available on all orders
Delivered across India
Toll Free: 1800 209 0998