Buy electronic modules online in India at Zbotic. Our extensive module collection includes relay modules, buck/boost voltage regulators, audio amplifiers, breakout boards, electronic keypads, laser modules, LED modules, logic level converters, piezo buzzers, potentiometer modules, RGB LED strips, RTC clock modules, solar panels, USB interface modules, and wearable electronics. These ready-to-use modules simplify electronics projects by providing pre-built functionality with easy microcontroller integration.
5V 1 Channel Relay Module
SKU: AI0018 ₹37.76 (₹32.00 + GST)
1 channel relay board
Operating Voltage 5V
Max Current: 20mA
Relay Contact Current Capacity at AC250V: 10A.
Relay Contact Current Capacity at DC5V: 10A
Power supply indicator lamp
Control indicator lamp
Triode drive, increasing relay coil
Add to cart
Add to Compare
RS485 to TTL Converter Module Serial Port UART Hardware Automatic Flow Control Module
SKU: AI0572 ₹41.30 (₹35.00 + GST)Quick Overview:
- Has a 120 ohm termination resistor, shorted R0 to enable the termination resistor.
- Support multi-machine communication, allowing access at up to 128 devices on the bus.
- The module can be hot swapped, the signal does not appear dead phenomenon.
- A large area of copper to prevent interference.
- Compatible with 3.3V and 5.0V power supply.
- Compatible with 3.3V and 5.0V signal.
MP3-TF-16P MP3 SD Card Module with Serial Port
SKU: AI0569 ₹88.50 (₹75.00 + GST)Supports sampling rates (KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48
24-bit DAC output, dynamic range support: 90dB, SNR support: 85dB
Fully supports FAT16, FAT32 file system
Maximum support 32G TF card
Support U disk to 32G, 64M bytes of NORFLASH
MAX485 TTL to RS485 Converter Module
SKU: AI0571 ₹35.40 (₹30.00 + GST)
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
A low power consumption for the RS-485 communication
Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
Slew-rate limited transceiver
All pins of the chip have been lead to can be controlled through the microcontroller.
Convenient RS-485 communication wiring
Multiple Units can be connected to the same RS-485 bus wiring.
All Chip pins are brought out for proper controls
Add to cart
Add to Compare
CD74HP4067 High Speed CMOS 16-Channel Analog/Digital Multiplexer Breakout Module
SKU: AI0149 ₹63.72 (₹54.00 + GST)
2V to 6V operation
“On” resistance: 70 Ohms @ 4.5V
6ns break-before-make @ 4.5V
Wide operating temperature range: -55C to 125C
Add to cart
Add to Compare
12V 3A Touch Sensor Switch for Mirror Light
SKU: AI0680 ₹141.60 (₹120.00 + GST)Quick Overview
- Output Line : 3 Line 150mm
- Input Line : Double Line 300mm
- Voltage : 12V
- Function : White Warm Two-Color Infinite Dimming
MP 1584 DC-DC 3A Adjustable Buck Module
SKU: AI0498 ₹90.86 (₹77.00 + GST)Input Voltage: 4.5V – 28V
Output Voltage: 0.8V – 20V
Output Voltage Adjustment: On-board potentiometer
Output Current: 1.8A (typical), 3.0A (max).
Ceramic Capacitor Stable
Internal Soft-Start
Internally Set Current Limit without a Current Sensing Resistor
DS1307 RTC I2C Module AT24C32 without Battery
SKU: AI0106 ₹48.38 (₹41.00 + GST)Interface: Two-wire I2C
Output Pin: 1Hz
Memory: 56 bytes non-volatile RAM
Battery: LIR2032 (included)
Operating Voltage: Standard 3V lithium cell (2V to 3.5V)
Package Options: 8-pin DIP or SOIC
Operating Temperature: Suitable for various environments
Dimensions: Compact and space-saving design
High Current Active Alarm Buzzer Driver Module
SKU: AI0112 ₹27.02 (₹22.90 + GST)
Operating voltage 3.3V-5V
PCB Dimensions: 29 (L) x 14 (W) x 12 mm (H)
Wire length: 20cm
Weight: 7 gm.
Frequency: 2500Hz
Add to cart
Add to Compare
ZMPT101B 2mA AC Single Phase Voltage Transformer Sensor Relay
SKU: AI0684Low price
Small size (49.5mm x 19.4mm) and lightweight
Easy PCB mounting
Good consistency
Widely acclaimed.
SMD 3 Color LED Module
SKU: AI0342 ₹40.83 (₹34.60 + GST)Quick Overview:
- RGB Trichromatic limiting resistor to prevent burnout
- PWM Adjusted Color Mixing
- Working Voltage: 5V
- LED Drive Mode: Common Cathode Driver
USB Type A Breakout Board – Male
SKU: AI0519 ₹8.85 (₹7.50 + GST)- USB Type: Type-A
- PCB Size : 15x15mm
PAM8403 5V Two-channel Stereo Mini Class-D 3W+3W Audio Amplifier
SKU: AI0607Quick Overview
- Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load)..
- Double panel wiring solves crosstalk.
- Super mini design allows it to be easily placed in a variety of digital products.
- 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply.
- Filter-less, Low Quiescent Current and Low EMI and Low Noise.
- Short Circuit Protection and Thermal Shutdown
150W DC-DC Step-Up Boost Converter 10-32V to 12-35V 6A Adjustable Power Supply Module
SKU: AI0176- Input voltage :10-32V
- Output voltage: 12-35V (adjustable)
- Output Current: 10A (MAX)
- Input Current: 16A (MAX) (Please enhance heat dissipation if more than 10A)
- The non-isolated step-up power conversion module
- Onboard LED illuminates when the voltage is applied to the module
- Equips Multi-turn Potentiometer.
DS3231 RTC Module Precise Real Time Clock I2C – AT24C02
SKU: AI0746Accuracy 2 ppm from 0° C to +40° C
Accuracy 3.5 ppm from -40° C to +85° C
Digital Temp Sensor Output: ±3° C Accuracy
Memory Chips: AT24C02 (2Kbit)
Register for Aging Trim
RST Output/Pushbutton Reset Debounce Input
Two Time-of-Day Alarms
Programmable Square-Wave Output Signal
Fast 400 Khz I2C interface
USB Fast Charging Module
SKU: AI1137 ₹69.62 (₹59.00 + GST)
Operating Voltage: 12 – 24VDC
Output Power: 36W
Supported Fast Charging Protocol: FCP,AFC,SFCP,SCP
Long Lifespan
TTP224 4-way Capacitive Touch Switch Module
SKU: AI0313 ₹86.14 (₹73.00 + GST)Quick Overview
- Onboard TTP224 capacitive touch sensor IC 4 keys
- 4 board-level status indicator
- Working voltage: 2.4V-5.5V
- Advanced Pins breakout, so that the output mode and working mode selectable.
- Low power selection
12V/24V to 5V 5A Power Module Dc-DC XY-3606 Power Converter
SKU: AI0582 ₹123.90 (₹105.00 + GST)Working voltage: DC 9V–36V
Output voltage: 5.2V/5A/25W
9~24V input: Output 5.2V/6A/30W
24~32V input: output 5.2V/5A/25W
32~36V input: output 5.2V/3.5A/18W
NE555 Delay Timer Switch Adjustable 5V Relay Module
SKU: AI0170 ₹102.66 (₹87.00 + GST)
NE555 Delay Timer Switch Adjustable 5V Relay Module Introducing the NE555 Delay Timer Switch Adjustable 5V Relay Module, your go-to...
Add to cart
Add to Compare
AMS1117-3.3 LDO 800MA DC 5V to 3.3V Step-Down Power Supply Module
SKU: AI0673 ₹16.17 (₹13.70 + GST)Quick Overview
- Product Name: AMS1117-3.3 LDO 800MA DC 5V to 3.3V Step-Down Power Supply Module
- Input Voltage: 4.5V to 15V
- Output Voltage: 3.3V to 5V
- Output Current: 800mA
- Onboard AMS1117 chip.
- Onboard power indicator to indicate power is turned on: Red LED.
- Output voltage interface, connection to facilitate the experimental.
- Small Compact Size, 3Pin Type, Breadboard Friendly.
CP2102 Micro USB to UART TTL Module 6Pin Serial Converter UART STC Replace FT232
SKU: AI0727 ₹178.18 (₹151.00 + GST)Quick Overview
- 5P – A type USB USB specification 2.0 compliant with full-speed 12Mbps.
- Standard USB type A male and TTL 5pin connector.
- 5pins for 3.3V, TXD, RXD, GND & 5V All handshaking and modem interface signals
- Baud rates: 300 bps to 1.5 Mbps.
- Byte receives buffer; 640 bytes transmit buffer.
1×4 Matrix – Membrane Type Keypad – 4 Keys
SKU: AI0522 ₹47.20 (₹40.00 + GST)- Ultra-thin design & adhesive backing provides easy integration to any project
- Excellent price-performance ratio
- Easy communication with any microcontroller
- 5 pins 2.54mm pitch connector, 4×1 type 4 keys.
- Sticker can peel off for adhesive mounting.
- Operating Voltage(VDC): 12
- Current : 30 mA
36W 3A Short Distance IR Hand Sweep ON-OFF Sensor Module
SKU: AI0666 ₹206.50 (₹175.00 + GST)Operating voltage: 12vDC
Output Voltage: 12 V
Output type: Double output
Detection range: adjustable 10-80 MM
Max Power Load: 36 W
Delayed off time: none
Field of application: DC, constant pressure
Load current: 3A optional
Standby current: 10mA
XL7015 DC-DC Step Down Adjustable Power Supply Buck Module
SKU: AI2176 ₹86.14 (₹73.00 + GST)Quick review :
- Input voltage range: 5V-80V DC
- Output voltage range: 1.5V-20V DC adjustable.
- Output current: 0-0.8A.
- High efficiency up to 90%
- Built-in thermal shutdown function
- Built-in current limit function
- Built output short protection function
Mini ENC28J60 Ethernet LAN Network Module
SKU: AI0360 ₹497.96 (₹422.00 + GST)Quick Overview:
- Fully Compatible with 10/100/1000Base-T Networks
- Integrated MAC and 10Base-T PHY
- Supports One 10Base-T Port with Automatic Polarity Detection and Correction
- Supports Full and Half-Duplex modes
- Programmable Automatic Retransmit on Collision
- Programmable Automatic Rejection of Erroneous Packets
- SPI Interface with Clock Speeds Up to 20 MHz
- For Arduino, SPI, AVR, PIC, LPC, STM32
PL2303 TA Download Cable USB to TTL RS232 Module USB to Serial
SKU: AI0613 ₹92.04 (₹78.00 + GST)Quick Overview
- Built-in TTL COM PC-PL2303HX Chip.
- Standard USB type and TTL 4 pin connector
- Simple and Easy way to give USB support to your designs
- Available for Linux, Mac, WinCE, and Windows (XP, 7), Win 8
- Cable Length: 1M
- Net Weight: 30gm
USB to RS485 TTL Serial Converter Adapter FT232
SKU: AI0326 ₹177.00 (₹150.00 + GST)Quick Overview:
- Baud rate: 300 – 9216000bps, automatically detecting the serial signal data rate
- Load capacity: support multipoint, each converter allows RS485 interface device to connect 32
- Interface Protection: TVS tube protection, USB self-recovery protection
- Support Windows98/ME/2000/XP/WIN7/Vista, Linux, Mac
- It can be up to 32 devices on the bus.
MT8870 DTMF Audio/Speech Decoding Telephone Module
SKU: AI0316 ₹99.12 (₹84.00 + GST)Quick Overview
- Working voltage: 5V
- Power Consumption: 500MW(MAX)r: 500 MW (MAX)
- On-board voice input interface
- On-board LED, it is very convenient to check the output state.
- Onboard 5 x LED indicators for easy viewing output state
- Operating Temperature: -40-+85 °C
- IO Drive: Current Maximum 10mA.
- PCB Size : 25.4×25.4MM
DC 3-5V X9C103S Digital Potentiometer Board Module for Arduino
SKU: AI0654 ₹210.04 (₹178.00 + GST)
Supply voltage: 3V-5V
Chip: X9C103S
Dimensions : 28 x 14 x 4 (LxWxH) mm.
10K span potentiometer.
Add to cart
Add to Compare
LilyPad LED Blue Color
SKU: AI0732 ₹29.50 (₹25.00 + GST)Wearable e-textile technology.
Available Various input, output, power, and sensor boards.
Washable
Airfly 5V Single Channel Relay Module (Made In India)
SKU: AI0532 ₹35.40 (₹30.00 + GST)Quick Overview
- 1 channel relay board
- Operating Voltage 5V
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
LilyPad LED Yellow Color(1pcs)
SKU: AI4109 ₹11.80 (₹10.00 + GST)LED Color: Yellow
Compatibility: LilyPad Arduino Boards
Dimensions: Small and lightweight for wearable integration
Voltage: Typically operates at 3.3V to 5V
Current Consumption: Depends on the specific LED and operating conditions
Connection: Designed for sewing onto fabric or textile
Features: Low power consumption, easy integration
Application: Wearable electronics, textile-based projects
SYD1230 6mm 650nm 5mW Red Line Laser Module
SKU: AI7231 ₹173.46 (₹147.00 + GST)Quick Overview
- Laser Output Type: Red LINE Laser
- Weight: 15 gm.
- Wavelength: 650nm
- Voltage: 3~6V
- Output Power: Min 2.5mW, Typical 3.0mW, Max 5.0mW
- Working current: Min 10mA, Typical 20mA, Max 25mA
- Working voltage: Min 2.3VDC, Typical 4.5VDC, Max 8.0VDC
1 Channel Relay Module, 30A with Optocoupler, Isolation 12V Supports, High and Low Triger
SKU: AI2962
QUICK OVERVIEW
- Channel: 1 channel
- Relay Voltage: 12V
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
LilyPad LED Red Color(1pcs)
SKU: AI4107 ₹8.09 (₹6.86 + GST)
This is a simple pack of five Red Lily Pad LEDs that are still attached to one another, letting you...
Add to cart
Add to Compare
DB9 RS232/485 9pin Terminal Male Screw with Shell,and Screw
SKU: AI3534
DB9 RS232 D-SUB Male Adapter 9-pin Port Adapter to Terminal Connector Signal Module
Suitable for variety of pin connections required to use serial communications industrial control products
No need solder! It is convenient
DB9 male adapter with screw
JQ6500 Voice Module MP3 Module MCU Serial Port Control Broadcast one-on-one 5 Way Control Music IC 16Mbit
SKU: AI0657 ₹231.28 (₹196.00 + GST)Quick Overview:
- Support all bit rate 11172-3 and ISO13813-3 layer3 audio decoding
- Sample rate support (kHz): 8 / 11.025 / 12 / 16 / 22.05 / 24 / 32 / 44.1 / 48
- Support Normal, Jazz, Classical, Pop, Rock and other sound effects
- UART interface: standard serial port, TTL level, baud rate can be set
- Input voltage: 3.2V–5V (best 4.2V)
- Rated current: 20mA
PCB Mounted Passive Buzzer Module
SKU: AI0651 ₹21.36 (₹18.10 + GST)Quick Overview:
- Operating Voltage: 1.5 ~ 15V DC
- Working Current: Less than 25mA
- Tone Generation Range: 1.5 ~ 2.5 kHz
- Dimensions (L x W x H): 19 x 15 x 10 mm
LilyPad LED Orange Color (1pcs)
SKU: AI4110 ₹15.93 (₹13.50 + GST)- LED Color: Orange
- Compatibility: LilyPad Arduino Boards
- Dimensions: Small and lightweight for wearable integration
- Voltage: Typically operates at 3.3V to 5V
- Current Consumption: Depends on the specific LED and operating conditions
- Connection: Designed for sewing onto fabric or textile
- Features: Low power consumption, easy integration
- Application: Wearable electronics, textile-based projects
AVR ISP 10 Pin to 6 Pin Adapter Board
SKU: AI0705 ₹52.27 (₹44.30 + GST)Quick Overview
- Made of high-quality material, practical and durable
- No. of Pinon USBASP side: 10.
- No. of Pinon Device under programming side: 6.
- Connector type on USBASP side: Male.
- Connector type on Device under programming side: Female.
- Header Pin Pitch: 2.54mm (0.1in).
- Pin Numbers Text: Yes on Top and Bottom sides of every pin.
AT24C256 I2C Interface EEPROM Memory Module
SKU: AI0646 ₹57.53 (₹48.75 + GST)Quick Overview:
- Chipset: FT24C256A
- Operating Temperature: -55°C to 125°C
- Storage Temperature: -65°C to 150°C
- The voltage on any pin with respect to ground: -1.0V to 6.25V
- Maximum Operating Voltage: 6.25V DC
LED Connector 4pin 10mm (Pack of 2)
SKU: AI5236 ₹31.86 (₹27.00 + GST)- LED Connector 4pin 10mm L Shape.
- The connectors of this wire are for strips which PCB board width is 10mm
- Suitable for RGB / RGBW / RGBWW color 5050 LED strips
24 Bit WS2812 5050 RGB LED Built-in Full Color Driving Lights Circular Development Board
SKU: AI3434 ₹166.38 (₹141.00 + GST)QUICK OVERVIEW:
- Outer Diameter: 89.5 mm.
- Supply Voltage: DC 4-7V.
- Communication interface: single wire communication.
- Send data at speeds of 800Kbps.
- The color of the light was highly consistent
- Full-color module, Full-color soft lights a lamp strip.
Human/Metal Touch Sensor Module
SKU: AI0136 ₹35.87 (₹30.40 + GST)Quick overview
- Operating Voltage: 5V DC
- Output: Analog/Digital
- Signal Output Indicator: Yes
- Power Supply Range: 2V to 5.5V DC
- Power Consumption: Low
- Installation: Four M2 screws positioning holes for easy integration
Ultra-Small Size DC-DC 5V 3A BEC Power Supply Buck Step Down Module
SKU: AI2148 ₹87.15 (₹83.00 + GST)- Input voltage: 7 – 26V
- Output voltage: 5V
- Output current: 3A (Max), the current should be controlled within 1.6A for working long hours
- Conversion efficiency: 96% (Max)
- Output ripple: < 30mV
Non-Destructive MP3 Decoding Board with Self-Powered TF Card U Disk Decoded Player Module
SKU: AI0606 ₹99.12 (₹84.00 + GST)Support MP3 format, playing power on automatically.
When mp3 is played the red LED flashes.
Support U disk (test 32G), TF Card (test 16G) play mode; power on default.
Buttons can be adjusted up and down to control songs, volume up and down, pause or play, mode switching.
Press menu button enter the single / all song play mode.
CJMCU MCP4725 I2C DAC Breakout Development Board
SKU: AI2172 ₹105.02 (₹89.00 + GST)Quick review :
- 12-bit resolution
- Small package
- 2.7V to 5.5V supply
- Internal EEPROM to store settings
- I2C Interface (Standard, Fast, and High-Speed supported)
LilyPad LED Green Color
SKU: AI0733 ₹29.50 (₹25.00 + GST)Wearable e-textile technology.
Available Various input, output, power, and sensor boards.
Washable
RDA5807M FM Stereo Radio Module RRD-102 V2.0 Wireless Pro for Arduino Tuner
SKU: AI0609Quick Overview
- Supply voltage: 2.7 to 3.3 V.
- Output Impedance: 32Ω.
- Frequency band: 50 -115 MHz.
- Digital auto gain control (AGC).
- Only support 2-wire bus interface.
NY-D01 100A Digital Display Spot Welding Controller Board
SKU: AI2951
QUICK OVERVIEW:
- Material: Plastic+Metal
- The controller is compatible with 100A scr.
- Digital control interface, you can display the current time and current settings.
- Time input 1-50, unit cycle (1 cycles is 20ms)
USB 3.1 Female Socket Type C Connector 24 Pins Breakout PCB Board
SKU: AI1131 ₹82.60 (₹70.00 + GST)
24 pin Breakout
PCB Size: 25 x 40 mm
Connector: C type Female
Add to cart
Add to Compare
RS232 to TTL Serial Interface Module 4 PINS
SKU: AI6497 ₹66.08 (₹56.00 + GST)- Based on Max3232 IC DB9 Connector 4pin Male header to interface with Arduino
- Operating Voltage: 3.3-5.5V
- It can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU
- Pre-assembled compact size board
- Suitable for use with most microcontrollers
PCF8591 Module Analog to Digital / Digital-Analog Converter Module
SKU: AI0616 ₹164.02 (₹139.00 + GST)Quick Overview
- Module chip using PCF8951
- Module supports external voltage input of the 4-way acquisition (voltage input range of 0-5v)
- The module integrated photoresistor by AD collection precise value of the ambient light intensity
- Module integrated thermistor by the precise value of the ambient temperature of the AD acquisition
- Module integrated 1 channel 0-5V voltage input acquisition (the blue potentiometer to adjust the input voltage)
- Modules with power indicator (for the module power supply indicator lights)
LilyPad Button Board Module For Arduino
SKU: AI0730 ₹21.24 (₹18.00 + GST)LilyPad is a wearable e-textile technology.
Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing.
Various input, output, power, and sensor boards are available.
5000W AC 220V High-Power Electronic Regulator SCR Voltage Regulator Module
SKU: AI2390 ₹374.06 (₹317.00 + GST)Operating Voltage: AC 220V
Maximum Power: 5000W
Voltage range (adjust temperature or light): 0-220V AC
High-temperature FR-4 PCB
100% High quality and Brand new
Shift Register Breakout – 74HC595 Board Module
SKU: AI0196 ₹96.76 (₹82.00 + GST)Quick Overview
- Product Name: Shift Register Breakout - 74HC595 Board Module
- SOIC version of the 74HC595 shift register IC
- The Serial in and out pins are on opposite sides of the board
- All pins from the IC are broken out to standard 0.1″ spaced headers.
Anti-Reverse Diode Constant Current Module 60V 10A For Backflow Protection Solar Constant Current Module Battery
SKU: AI3361 ₹35.40 (₹30.00 + GST)- Type: Voltage Regulator
- Operating Temperature: -40-+85
- Supply Voltage: 60v
- Dissipation Power: 10A
- Package: SMD
DC-DC 1.8V-5V to 3.3V, Booster and Buck Power Modules
SKU: AI5213 ₹48.38 (₹41.00 + GST)- Input Voltage: 1.5V to 5V DC
- Output Voltage: 3.3V DC
- Dimensions (L x W)mm: 11 x 7
6-20V 1-Channel Power Relay Module with Adjustable Timing Cycle
SKU: AI2788 ₹142.78 (₹121.00 + GST)QUICK OVERVIEW:
- Operating voltage: 6-20V
- Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustable.
- Optocoupler Isolation.
5V 8 Channel Relay Module
SKU: AI0054 ₹349.28 (₹296.00 + GST)Quick Overview :
- Product Name: 5V 8 Channel Relay Module
- Channel: 8 channel
- Relay Operating Voltage: 5V
- Power supply and relay instructions, lit, disconnect is off;
- Input signal, signal, common Terminal and start conducting;
- Input signal, signal, common Terminal and start conducting;
- Useful for appliance control;
- DC or AC signal, control, you can control the 220V AC load;
- There is a normally open and one normally close contact;
- The module is compliant with international safety standards, control and load areas isolation trenches.
12V 3A Double Color Dimmable LED Light Dimmers Mirror Touch Sensor Switches
SKU: AI1536 ₹166.38 (₹141.00 + GST)Working Voltage : 12VDC
Max Load : 3A 36W Max
LED Indicator : Blue (ON Mode); White (OFF Mode)
Cable Length : Input – 10cm；Output – 10cm
Color Available : Black
Dimension : 42 x 33 x 8mm
Support Mirror Thickness : ≤ 5mm
CH340G USB to RS232 TTL Auto Converter Adapter Module for Arduino
SKU: AI0648 ₹80.24 (₹68.00 + GST)Quick Overview:
- Resettable fuse with 500mA
- 3.3V / 5V real switchable
- 3.3V comes with the transformer
- Green Data reception indicator
- Multifunction CTS access products
- Dual protection circuit
- Full-function pins 5P
- Blue power indicator
Dual USB Output 9V / 12V / 24V / 36V Car Charger Switch 5V DC-DC Power Supply Module 3A Buck Regulator
SKU: AI5239- Input : 6V-40V
- Output : 5V / 3A (MAX)
- Efficiency : 92% (MAX)
- Switching frequency : 150KHZ
- High efficiency and low ripple.
- With USB power indicator light.
- Maximum output 3A (at the same time with two mobile phones).
250W High Power Constant voltage Current Adjustable Aluminum Substrate LED Driver Module
SKU: AI2370 ₹296.18 (₹251.00 + GST)
Stabilized Power Supply DIY: Create a stable power source from a 12V input, adjustable from 12V to 50V.
Electronic Equipment Power: Customize output voltage to match your device’s requirements for reliable operation.
Car Power Enhancement: Power laptops, PDAs, and digital devices on-the-go using your car’s supply.
High-Power Mobile Solution: Pair with a 12V lithium battery pack for a robust notebook power source.
Solar Panel Voltage Regulation: Ensure efficient solar panel performance by regulating voltage output.
Battery Charging: Safely charge storage and lithium batteries with adjustable settings.
LED Light Driving: Drive high-power LED lights with stability and precision control.
Add to cart
Add to Compare
LM7805 5V DC / AC Three Terminal Voltage Regulator Power
SKU: AI3857 ₹102.66 (₹87.00 + GST)5V LM7805 DC/AC Three Terminal Voltage Regulator Power Supply Module Output Max 1.2A
With good peformance and high quality material, it may work for a long time.
Provide a full protection from dust, shock, scratches and bumps and other daily damage
Completely fits and works
Simple and easy, comfortable, easy to carry
DC-DC 4.5-40V To 5V 2A USB Charger Step down Converter Voltmeter Module
SKU: AI0302 ₹199.42 (₹169.00 + GST)Quick Overview
- Input voltage: DC 4.5 ~ 40V.
- Output voltage: 5V (when the input voltage is between 6.5V ~ 40V).
- Output current: 2A.
- The voltmeter has an automatic calibration function.
- With reverse connection protection.
- With overheat protection and short circuit protection.
DS3231 Real Time Clock Module 3.3V 5V Precise
SKU: AI0846 ₹332.76 (₹282.00 + GST)
Supply voltage(V):+3.3 to +5.5
operating temperature range:-40°C to +85°C
Supported Raspberry Pi and Arduino
Provide battery backup for continuous timing.
Two calendar alarm.
1Hz and 32.768kHz output.
Waveshare Industrial Serial Server, RS485 to RJ45 Ethernet, TCP/IP to Serial, Rail-Mount Support
SKU: AI0826 ₹2,240.82 (₹1,899.00 + GST)
Terminal RS485 interface
Support 32 slave devices
Baud rate support 300~115200bps
Support MQTT gateway function.
Operating temperature -40~85℃
5V Double Channel Relay Module (Made In India)
SKU: AI0531 ₹82.60 (₹70.00 + GST)Quick Overview
- High current relay, AC250V 10A, DC5V 10A
- 2 LEDs to indicate when relays are on
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
FR120N MosEFT control Module Replacement Relay
SKU: AI1535 ₹38.94 (₹33.00 + GST)- Model: FR120N
- MOS tube: 100V 9.4A
- Dimensions: 33mm X 17mm
- Mounting Holes Diameter: 2mm
- Compatible with MCU and control board, 3V or 5V signal.
- High-level start, low-level stop, PWM speed regulation.
1000KV Step Up Power Module
SKU: AI5285Input Voltage: DC3.6V-6V
Input Current: 2A-5A
Output Voltage: DC 500KV-1000KV (Please pay attention to safety when used)
Input Line Length: about 100mm (red is positive)
Output Line Length: about 160mm
5-24V MINI 3Key LED Controller for WS2811 WS2812B LED Light Strip with Red+Black Cable
SKU: AI4132 ₹83.78 (₹71.00 + GST)- Operating Voltage: DC5V-24V (Choose according to voltage rating of your LED strip)
- Control Range – 2048 pixels
- Supported IC – WS2812, WS2811 based LED strips
Micro USB Type B Mike Patch Straight Plug Adapter Plate Welding Head-(Pack of 2)
SKU: AI2535QUICK OVERVIEW:
- MICRO USB ( 5pin, B type, female connector )
- Base Material: FR4.
- Board Thickness: 1.6mm.
- Size: 16 x 14.5 mm .
16Bit WS2812B 5050 RGB LED Built-in Full Color Driving Lights Circular Development Board
SKU: AI3433QUICK OVERVIEW:
- Outer Diameter: 68 mm.
- Supply Voltage: DC 4-7V.
- LED driver chip: WS2812B
- Communication interface: single wire communication.
- Send data at speeds of 800Kbps.
- The color of the light was highly consistent
- Full-color module, Full-color soft lights a lamp strip.
DC-DC DC8-55V to 5V 2A Step Down Buck Module Regulated Power Supply Module 2A High Current Circuit Board
SKU: AI2452 ₹178.18 (₹151.00 + GST)QUICK OVERVIEW:
- DC-DC DC8-55V to 5V 2A Step Down Buck Module Regulated Power Supply Module
- Model type: DC-DC Step Down Power Supply Module
- Size: 26 x 17.2mm
- Input voltage: 8-55V
- Output voltage: 5V
- Dissipation Power: 2A
2 Channel Logic Level Converter 3.3V 5V TTL
SKU: AI3420 ₹23.60 (₹20.00 + GST)QUICK OVERVIEW:
- Material: Plastic + metal
- Portable, small, easy to use.
- Comes with 2 rows of 6pin, unsoldered.
- The compatible breadboard can be directly inserted into the breadboard.
5V 1A USB Booster Cable DC5.5*2.1MM 9V
SKU: AI3759 ₹212.40 (₹180.00 + GST)Great for short distance connection
Simply & Professional appearance for cabling
Easier for installation save time and money
Easy to use.
Precision 12V 450mA (5W) power Supply Module Bare Board, LED Voltage Regulator Module AC 220V to 12V
SKU: AI2575 ₹143.96 (₹122.00 + GST)
QUICK OVERVIEW:
- Input Voltage: 220VAC
- Output Voltage: 12 VDC.
- Output Power: 5W.
- Output overload and short circuit protection.
12V 5050 RGB LED Strip Controller box with 24 Key IR Remote Control
SKU: AI3474 ₹178.18 (₹151.00 + GST)QUICK VOERVIEW:
- Plug and Play Easy to connect
- Flexible IR Receiver Probe
- Multi-Function IR Remote control
- 16 colors, 5 light pattern: Static/Flash/Strobe/Fade-change/RGB Smooth-change.
- 16-classes Static Mode Dim Control
- 16-Speeds Control in Flash / Strobe / Fade-change / RGB Smooth-change.
- Connecting mode: common anode
7 Color Flashing LED Module
SKU: AI1584 ₹33.04 (₹28.00 + GST)- Product Type: LED
- Shape: Round LED 5mm DIP type
- Color: pink yellow-green (high brightness)
- Lens type: white mist
- Standard Forward Voltage:3.0-4 .5 V
Free Shipping
On orders above ₹999
COD Available
Min. order ₹250 for COD
GST Invoice
Available on all orders
1,50,000+ Orders
Delivered across India
Expert Support
Toll Free: 1800 209 0998
Product categories
- Show All Categories
- 3D Printers and Parts (379)
- Batteries, Chargers and Accessories (811)
- Clearance Sale (0)
- Development Boards (438)
- DIY Learning and Robot Kits (117)
- Drone Parts (1364)
- EBike parts (140)
- Electronic Components (783)
- Electronic Modules and Displays (1201)
- FPV Freestyle Mid/High KV Drone Motors (0)
- IoT and Wireless (544)
- Mechanical Parts and Workbench Tools (241)
- Motors & Drivers & Pumps & Actuators (583)
- Sensor Modules (639)
- Electronic Modules and Displays (1201)
- Character LCD Displays (2)
- Display modules (265)
- Electronic Modules (755)
- Audio Amplifier Module (51)
- Breakout Board (40)
- Buck Boost Voltage Regulators (158)
- Electronic Switches/Keypads Modules (49)
- LASER Module (12)
- LED Module (13)
- Logic Level Converter (6)
- Piezo Buzzer Module (7)
- Potentiometer Module (3)
- Relay Modules (175)
- RGB LED Strips and Drivers (36)
- RTC Module (16)
- Solar Panels and Controllers (8)
- USB Interface Module (160)
- Wearable Electronic (21)
- Measuring Instruments (102)
- Power Supply (62)
- Signal Generator Module & Oscilloscopes (17)