Buy electronic modules online in India at Zbotic. Our extensive module collection includes relay modules, buck/boost voltage regulators, audio amplifiers, breakout boards, electronic keypads, laser modules, LED modules, logic level converters, piezo buzzers, potentiometer modules, RGB LED strips, RTC clock modules, solar panels, USB interface modules, and wearable electronics. These ready-to-use modules simplify electronics projects by providing pre-built functionality with easy microcontroller integration.
Conversion efficiency: <94% (greater the pressure, the lower the efficiency)
Switching frequency: 400KHz
Output Ripple: 50mV (the higher the voltage, the greater the current, the greater the ripple)
Load Regulation: ± 0.5%.
Voltage Regulation: ± 0.5%
Operating Temperature: -40 ~ 85
Supports momentary or latching/toggle modes
Supports Active High or Active Low output signal modes
Dimensions: 15mm x 11mm
Input Voltage: 2V-5.5V DC
The response time max ~ 60mS in fast mode, ~220mS at low power mode @VDD=3V
Sensitivity can adjust by the capacitance (0~50pF)
Overview
Supports sampling rates (KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48
24-bit DAC output, dynamic range support: 90dB, SNR support: 85dB
Fully supports FAT16, FAT32 file system
Maximum support 32G TF card
Support U disk to 32G, 64M bytes of NORFLASH
Dual MOSFET
Trigger Source: 3.3V to 20V DC
Signal Frequency: 0-20KHz Supported
Output Drive Capacity: 5V to 36V DC
Continuous Current: 15A at Room Temperature
Input Voltage(VDC): 4 ~ 40.
Output Voltage(VDC): 1.3 ~ 37.
Output Current: 2A Rated, ( 3A maximum with heat sink).
Switching Frequency: 150 kHz.
Input reverse polarity protection.
Built-in output short protection function.
Matrix: 4×4 Matrix Membrane Keypad
Connector: 8-pin connector
Mounting: Adhesive mounting with sticker on the back side
Operating Temperature: 0 to 60 degrees Celsius
Humidity: 40 degrees Celsius, 90%-95% (240 hours)
Flexible Circuit Length: Approximately 3.3 inches (83 mm)
5V power supply.
Serial I2C control of LCD display using PCF8574.
Backlight can be enabled or disabled via a jumper on the board.
Contrast control via a potentiometer.
Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Input Voltage: 4.5V – 28V
Output Voltage: 0.8V – 20V
Output Voltage Adjustment: On-board potentiometer
Output Current: 1.8A (typical), 3.0A (max).
Ceramic Capacitor Stable
Internal Soft-Start
Internally Set Current Limit without a Current Sensing Resistor
Input voltage range: 5-5.5V
Charging cut-off voltage: (4.2V/4.35V) ±0.5%:
Charging current: 2.4A±5%
Boost output voltage: 5V5.15V (wire loss compensation)
Boost output voltage ripple: 100mV
Interface: Two-wire I2C
Output Pin: 1Hz
Memory: 56 bytes non-volatile RAM
Battery: LIR2032 (included)
Operating Voltage: Standard 3V lithium cell (2V to 3.5V)
Package Options: 8-pin DIP or SOIC
Operating Temperature: Suitable for various environments
Dimensions: Compact and space-saving design
Onboard LM386 Chip.
200 multiplier benefits circuit design.
On-board speaker wiring Block.
On-board 10K variable resistor, you can adjust the volume of the enlarged.
Onboard Power Indicator.
It can be used with NRF24L01 wireless module
Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
Allows for easy connection to nRF24L01+ modules
Small power on SMD LED indicator
Input Voltage:DC 4.5-24V
Module Size: 10 x 20 mm
Adjustable Range:0.8-17V,fixed voltage (1.8V 2.5V 3.3V 5V 9V 12V)
Output Current:3A (max),actual testing input 12V output 1.5A
Transform Efficiency:97.5%(max) (6.5 to 5V 0.7A)
Switch Frequency:500KHz
Output Ripple Wave:20mV (12V to 5V 3A) 20m band width
QUICK OVERVIEW
QUICK OVERVIEW:
Bluetooth V4.2 version, support Bluetooth automatic connection technology,
Support WAV/WMA/FLAC/APE/MP3 lossless decoding, stereo dual channel output.
5V 4-Channel Relay interface board and each one needs 15-20mA Driver Current.
Equipped with high-current relay, AC250V 10A; DC30V 10A.
Standard interface that can be controlled directly by microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
Indication LED’s for Relay output status.
Operating voltage: 12vDC
Output Voltage: 12 V
Output type: Double output
Detection range: adjustable 10-80 MM
Max Power Load: 36 W
Delayed off time: none
Field of application: DC, constant pressure
Load current: 3A optional
Standby current: 10mA
Working voltage: DC 9V–36V
Output voltage: 5.2V/5A/25W
9~24V input: Output 5.2V/6A/30W
24~32V input: output 5.2V/5A/25W
32~36V input: output 5.2V/3.5A/18W
Wide voltage power supply (6~30V)
supports micro USB 5.0V power supply
The interface is clear and simple, powerful, easy to understand
All set parameters automatically save power.
QUICK OVERVIEW
On-board level shift circuit
Arduino UNO R3 and the compatible board can directly connect to this module;
Interface logic voltage: 3.3V / 5V compatible(On-board level shift circuit);
Working voltage: 4.5~5.5V (Onboard 3.3V LDO Regulator);
Working current: 240mA(MAX).
Digital signal output
18B20 Temperature Sensor Chip
Resolution adjustment ranges from 9-12 bytes.
Send data via a pin
Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.
Wearable e-textile technology.
Available Various input, output, power, and sensor boards.
Washable
LED Color: Yellow
Compatibility: LilyPad Arduino Boards
Dimensions: Small and lightweight for wearable integration
Voltage: Typically operates at 3.3V to 5V
Current Consumption: Depends on the specific LED and operating conditions
Connection: Designed for sewing onto fabric or textile
Features: Low power consumption, easy integration
Application: Wearable electronics, textile-based projects
Product: DC Conversion Power Module
Input Voltage Range:2.8V-5.5V
Output Voltage:+/-12V (V +:+12V;V-:-12V)
Output Current:+12V stable output current capability of 50mA,-12V stable output current capability 30mA,almost meet all ADC, DAC and amplifier applications
Size:2.4×1.2cm
5V Tolerant Inputs.
Supports Hot Insertion.
I2C Bus and SMBus Compatible.
Low Standby Current.
1-to-8 Bidirectional Translating Switches.
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II.
Active-Low Reset Input.
Power Up With All Switch Channels Deselected.
DB9 RS232 D-SUB Male Adapter 9-pin Port Adapter to Terminal Connector Signal Module
Suitable for variety of pin connections required to use serial communications industrial control products
No need solder! It is convenient
DB9 male adapter with screw
Bluetooth version: 4.2
Supply current: 1A
Power supply voltage: 5V
Max. Audio Output Power: 10W
No soldering Required on Module
Input Voltage: DC3.6V-6V
Input Current: 2A-5A
Output Voltage: DC 400KV (Please pay attention to safety when used)
Input Line Length: about 100mm (red is positive)
Output Line Length: about 160mm
QUICK OVERVIEW:
Input voltage: 4-40VDC,
Output voltage: (1.25-36V) continuously adjustable (recommended load debugging).
Efficiency: 94%
Output current: 8A(max)
Output Power: 200W (max)
QUICK OVERVIEW
QUICK OVERVIEW:
Wearable e-textile technology.
Available Various input, output, power, and sensor boards.
Washable
Voltage: 3.3V or 5V.
Port: Analog.
Resistance: 10K.
Dimensions: 91 x 21 x 30 mm(LxWxH)
Weight: 18 gm.
Compatible Chips:
ATMEGA Series
Tiny Series
Classic Series
CAN Series
PWM Series
Built-in Industrial Micro-Controller
Big LCD Display
All Adjustable Parameters
Full 4 Stage PWM Charge Management
QUICK OVERVIEW:
On orders above ₹999
Min. order ₹250 for COD
Available on all orders
Delivered across India
Toll Free: 1800 209 0998