Input voltage: 4-40VDC,
Output voltage: (1.25-36V) continuously adjustable (recommended load debugging).
Efficiency: 94%
Output current: 8A(max)
Output Power: 200W (max)
QUICK O VERVIEW:
Cable Length: 15 cm
Gender: Male
Easy to use
Flexible neck for longer life
QUICK OVERVIEW
QUICK OVERVIEW
Product: Test Hook Clip Test Probe
Color: Red
Total Length: 43mm (Approx. 1.7 inches)
Overall Length: Approx. 4.2 cm
QUICK OVERVIEW
Quick review :
Material: Sponge
Color : Yellow
Size: 5cm*3.5cm*1mm
MOSFET Type: P-Channel
Package Type: TO-220
Voltage Rating (Vds): 55V
Current Rating (Id): 31A
Technology: HEXFET
Dynamic dv/dt Rating: Yes
Switching Speed: Fast
Avalanche Rating: Fully rated
Low noise operation.
Small fog particles.
High stability.
Driving Voltage: DC 5V.
High Conversion Efficiency.
Low Impedance Stable Waveform.
Resonance Frequency: 4.6 kHz +/- 0.5 kHz
Resonance Impedance: 200 Ohms
Capacitance: 20nF +/- 30% at 1 kHz
Operating Temperature: -20°C to +70°C
Storage Temperature: -30°C to +80°C
QUICK OVERVIEW:
Wire Type: 22AWG
Working Voltage: 300V
Working Current: 2A
Temperature Resistance: 80° C
Cable Length: 70cm
Product: Test Hook Clip
Color: Black
Total Length: 43mm
Overall Length: Approx. 1.7 inch / 4.2 cm
Easy to use.
QUICK OVERVIEW
QUICK OVERVIEW
Product Name: 110 RPM Half Metal Gear BO Motor – Straight (DOUBLE SHAFT)
Series: BO Series
Gear Type: Half Metal Gear
Operating Voltage: 3~6V DC
Shaft Length: 8.5mm
Shaft Diameter: 5.5mm (Double D-type)
No Load Current: 40-180mA
Rated Speed (After Reduction): 110 RPM
Rated Torque: 1 Kgcm
Compatibility: Compatible with 69mm Diameter Wheel for Plastic Gear Motors and 87mm Diameter Multipurpose Wheel for Plastic Gear Motors
Motor Type: DC Motor
Alligator Clip Length (without silicone cover): approx 28mm
Housing: Insulating paste resin
Insulating Material: Silicon
Withstand voltage: 300V~5A; Rated current: 10A
The thickness of clip: about 0.5mm; Opening range of clip: 10mm
Small alligator clip: except the length of the rubber sleeve is 2.8CM, the width of the clip is 4MM crocodile clip + thicken protective insulation sleeve
Self-locking/Latching Self-reset
Good electrical conductivity
This is Momentary type push-button switch
Easy to use
Light Weight
Function: Momentary
Operating Voltage: 3.3 ~ 5.5 VDC.
Operating Current: 5mA.
Interface: PH2.54-3P.
Dimensions mm(LxWxH): 98 x 23 x 4.
Supports 3-Pin Gravity Sensor interface
Analog output.
Weight (gm): 15.
QUICK OVERVIEW:
Model: ESP WROOM 32 MCU
Processor: Single or Dual core Tensilica Xtensa 32-bit LX6
Operating voltage (v): 2.3 ~ 3.6
Operating current (mA): 80
Small volume, easily embedded to other products
Strong function with support LWIP Protocol, Freertos
QUICK OVERVIEW:
QUICK OVERVIEW:
Made From High-Quality Materials.
Electronic High-Frequency Oscillations (2.4MHz).
Material: Ceramic, Wire
Diameter: Atomizer: 2cm/0.79in; Sealing ring: 2.5cm/0.98in
QUICK OVERVIEW
Model number: TEC1-12715
Operating Voltage: 12V
Maximum Voltage- Umax (V) : 15V
Maximum Current- Imax (A) : 15A
Maximum Power : 230 W
Power Cord: 25cm.
QUICK OVERVIEW:
High sensitivity to Ammonia, Sulfide and Benzene
Stable and Long Life
Detection Range: 10 – 300 ppm NH3, 10 – 1000 ppm Benzene, 10 – 300 ppm Alcohol
Heater Voltage: 5.0V
Dimensions: 18mm Diameter, 17mm High excluding pins, Pins – 6mm High
Long life and low cost
Plug-n-play.
Easy to use.
Components are easily interconnected using 20-28 AWG wire.
2.54 mm hole spacing
ABS plastic material
Model: MG90S
Weight: 13 gm
Operating voltage: 4.8V~ 6.6V
Servo Plug: JR
Stall torque @4.8V : 1.8kg-cm
Stall torque @6.6V : 2.2kg-cm
QUICK OVERVIEW:
Size: 0.96 inch
Resolution: 128 x 64
Controlling Chip: SSH1106
Display Area: 21.74 x 10.86mm
Driving Voltage: 3.3-5V
Operating Temperature: -40~70 degrees Celsius
Interface Type: IIC
Light Color: White
QUICK OVERVIEW:
QUICK OVERVIEW:
Capacity (Kg): 50.
Output Sensitivity (mv/v): 1.0±0.1.
Nonlinearity (%FS): 0.03.
Repeatability (%FS): 0.03.
Input Resistance (Ω): 1000.
Insulation Resistance (MΩ): ≥5000.
Fully calibrated
Digital output, I²C interface
Excellent long-term stability
Quick response and strong anti-interference ability
This 15mm Inner Diameter Zinc Alloy Pillow Block Flange Bearing KFL001 is a quality flanged ball bearing end mount, widely used in CNC and 3D printing applications. Made from a zinc-aluminum alloy, which supports linear shafts, leadscrews or ball screws. Secured using two grub screws, this bearing mount is a convenient option for your project
Easy Installation
A Low Current Consumption
Wide View Angle
QUICK OVERVIEW
Model: 18650 radiating battery spacer.
Material: ABS/PC (Remarkable Flame Retardant Plastic).
Bore Diameter: 18.5mm
Combined them into many different sizes and shapes of the battery pack.
Application: Design for Radiating Complex Battery Packs. Safe and Stable, Perfect Build for eBike!
Voltage: 3.3V or 5V.
Port: Analog.
Resistance: 10K.
Dimensions: 91 x 21 x 30 mm(LxWxH)
Weight: 18 gm.
Fuse Holder-BF-020:
QUICK OVERVIEW:
Compatible Chips:
ATMEGA Series
Tiny Series
Classic Series
CAN Series
PWM Series
On orders above ₹999
Min. order ₹250 for COD
Available on all orders
Delivered across India
Toll Free: 1800 209 0998