QUICK OVERVIEW:
Magic tape with buckle, ideal for power Li-Po battery management
Organize your batteries more simple, easy to find.
Material: Nylon
Length: 30 CM
Width: 20 mm
Quick review :
Contact Rating: 10 W.
Switching Voltage: 220 V.
Switching Current: 0.5 A.
Breakdown Voltage: 220 VDC.
Carry Current: 1 A.
Contact Resistance: 100 mΩ.
28-Pins in a Dual In-Line Packaging (2×14 pins)
Capabilities: SPI, I2C, USART, PWM
2.7V – 5.5V Input Voltage Range
1µA – 1.5mA Power Consumption (3V)
10-bit Analog-to-Digital Converter (8-channels)
Interrupt Capabilities (2-channel)
32KB of Flash Memory for Programming
3S 11.1V 12.6V 40A 18650 lithium battery protection board (comes with recovery function-AUTO Recovery)
Application: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650.26650, a polymer lithium battery)
Continuous discharge current (upper limit): 40A (if the cooling environment is not good, please reduce the load current use)
Continuous charge current (upper limit): 20A
Type: Photoresistor (Light Dependent Resistor)
Operating Principle: Photoconductivity
Dark Resistance: Greater than 200 MΩ
Light Resistance: Less than 2.4KΩ
Sensitivity: High sensitivity to varying light levels
Diameter: 5mm
Color: White (Note: Color may vary based on availability)
Material: High resistance semiconductor
Operating Temperature: -40°C to +70°C
4-level LED lamp display power, not working state intelligent automatic shutdown.
Dual USB output ports.
Input port: MicroUSB (Andro).
Output port: USB.
Output parameters: 5V1A / 5V2A.
IC Name: IRF 9540
Package/Case: DIP-3
DB9 RS232 D-SUB Male Adapter 9-pin Port Adapter to Terminal Connector Signal Module
Suitable for variety of pin connections required to use serial communications industrial control products
No need solder! It is convenient
DB9 male adapter with screw
Channel: 1 channel
Relay Voltage: 5V
High impedance controller pin
Pull-down circuit for the avoidance of malfunction
One normally closed contact and one normally open contact
Triode drive, increasing relay coil
QUICK OVERVIEW
Quick review :
QUICK OVERVIEW:
MODEL NO: CW-113-V1.1
Input Voltage: AC 100 – 240 V (50 HZ/60 HZ).
Output Voltage: DC 24V.
Output Current: 6A to 9A (no voltage drop).
Output Power: 150W (maximum 220 W).
Overload Protection: Yes.
Over Current Protection: Yes.
Short Circuit Protection: Yes.
Dual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor.
Operating voltage: 2.7 V to 10.8 V
Output current: 1.2 A continuous (2 A peak) per motor.
Inputs are 3V- and 5V-compatible.
5V Tolerant Inputs.
Supports Hot Insertion.
I2C Bus and SMBus Compatible.
Low Standby Current.
1-to-8 Bidirectional Translating Switches.
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II.
Active-Low Reset Input.
Power Up With All Switch Channels Deselected.
QUICKOVERVIEW
Single Battery Charger Module
Programable Charge Curren Form 0.1A to 2A
Programable Precharge Current Form 10% to 100%
Based on Tp5000 Battery Charger IC
Product Name: Metal Button Switch
Hole diameter: 12mm
Material: Nickel plated brass
LED color: Red
Shell Color: Silver
Max current: 4A
Led voltage: 12-24V
Operation type: Momentary Self-reset
Switch contact : Flat head /High head
Waterproof level:IP66
Contact type:1NO1NC
Plug Type: JR Male To futaba female Servo Extension Wire.
Cable Length: 30 cm
There is a 3-pin connector on both ends.
It fits for Futaba female and JR male
It is useful for RC Car, plane, helicopter, and drone servo connection or receiver connection.
Working Voltage : 3 – 5.5V.
The maximum Current : 49mA 5V.
Range : 20cm to 800 cm
Operating Voltage: 3.3 ~ 5.5 VDC.
Operating Current: 5mA.
Interface: PH2.54-3P.
Dimensions mm(LxWxH): 98 x 23 x 4.
Supports 3-Pin Gravity Sensor interface
Analog output.
Weight (gm): 15.
QUICK OVERVIEW
Self-locking/Latching Self-reset
Good electrical conductivity
This is Momentary type push-button switch
Easy to use
Light Weight
Function: Momentary
Bluetooth version: 4.2
Supply current: 1A
Power supply voltage: 5V
Max. Audio Output Power: 10W
No soldering Required on Module
Model No.: XH-W3001
Operating Voltage Range: 6 to 12V
Rated Power (W): 120W
Rated Current: 10 Amp Max.
Measurement Input: NTC10K
Temperature Measuring Range:-50C~110C
Temperature Control Range:-50C~110C
Control Accuracy: Upto 0.1
Measuring Accuraccy: 0.2
Quick Overview:
Input Voltage: AC 220V
Maximum Power Handling: 4000W
Control Method: Thyristor SCR (Silicon Controlled Rectifier)
Compatibility: Suitable for controlling various 220V appliances
Usage: Light dimming, fan speed control, stove temperature regulation, etc.
Adjustment Range: Output voltage adjustable between 0 – 220 volts
Material: Sponge
Color : Yellow
Size: 5cm*3.5cm*1mm
40P color DuPont line
Length: 300mm
Weight: 45 gm
Compatible with 2.54mm spacing pin headers
40pcs chromatic female to female color jump wire
High quality and in good working condition
Durable and reusable
Easy to install and use
QUICK OVERVIEW
Product: Test Hook Clip
Color: Black
Total Length: 43mm
Overall Length: Approx. 1.7 inch / 4.2 cm
Easy to use.
QUICK OVERVIEW
Voltage: DC 2.4V – 5V
Average Current Consumption: < 2mA
Output mode: level or UART
Detection distance: 2cm – 450cm
Working temperature: -20°C to +70°C
It features temperature compensation.
Provides two output modes level or UART.
On orders above ₹999
Min. order ₹250 for COD
Available on all orders
Delivered across India
Toll Free: 1800 209 0998