This is the 5mm variant of the 40A 2-6S ESC 3.5mm Banana connector in (ESC) Drone Speed Controller. Available at ₹850.50 (₹810.00 + GST) with free shipping across India.
Looking for 40a Connector? 40A 2-6S ESC 3.5mm Banana connector is available at Zbotic with fast shipping across India.
40A 2-6S ESC 3.5mm Banana connector
An opto ESC isolates the high-power side (battery and motor) from the signal side (connection to the receiver) by internally transmitting the receiver throttle signal from the input side to the output side of the ESC through an opto-coupler.
ReadytoSky 40A 2-6S ESC is specifically made for quadcopters and multi-rotors. Which provides faster and better motor speed control giving better flight performance compared to other available ESCs.
ReadytoSky 40A 2-6S ESC comes with a multi-integrated special program, fast throttle response, surpasses all kinds of open-source software. Firmware was optimized specifically integrated circuitously for the disc motor, and it has very good compatibility and this ESC is compatible with 2-6s Lipo Battery.
Due to ultra-low resistance MOSFET, it has a strong flow capacity. With MOSFET special driver integrated circuit, its performance and stability far surpass the driving circuit with discrete components built.
If you are wandering to build a drone and don’t know what will be the best ESC for you then worry no more, we have got your back. At Robu, we have everything for you to get started with your drone project.
Note: Black wire does not include with ESC.
Features:
- Using Multi integrated circuit opted special program, fast throttle response, surpasses all kinds of open-source software
- Firmware was optimized specific integrated circuit ally for disc motor, and it has a very good compatibility
- Highly intelligent, strong adaptive capacity, reserve the timing setting item (height/middle timing), easy to use
- Throttle signal line is twisted wire to reduce crosstalk within the transmission signal generated by the copper, so that more stable flight
- Supports refresh rates up to 621Hz throttle signal, compatible with various flight controllers. (Note: the throttle signal over 500Hz are all non-standard throttle signal)
- Using MOSFET special driver integrated circuit, its performance and stability far surpass the driving circuit with discrete components built
- Ultra-low resistance MOSFET, strong flow capacity
Specification:
| Model | ReadytoSky 2-6S 40A |
|---|---|
| Current Rating (A): | 40 |
| Burst Current (A) | 60 |
| BEC | NO |
| Cell | Lipo Cell 2-6S |
| Firmware | Hobbywing Xrotor 40A |
| Connector | 3.5mm Banana connector |
| Shipping Weight | 0.034 kg |
| Shipping Dimensions | 12 × 9 × 2 cm |
Packages Includes:
1 x 40A 2-6S ESC 3.5mm Banana connector
40A 2-6S ESC 3.5mm Banana connector Overview
The ReadytoSky 40A 2-6S ESC with 3.5mm banana connectors is an opto-isolated speed controller designed for quadcopters and multi-rotor drones. It handles up to 40A continuous current (60A burst for 10 seconds) across 2-6S LiPo packs, delivering precise throttle response and stable motor control.
Key Features of 40A 2-6S ESC 3.5mm Banana connector
- 40A continuous current handling with 60A 10-second burst capacity
- Supports 2S to 6S LiPo battery voltage range for flexible power setups
- Opto-coupler isolation between power and signal circuits for reduced interference
- Programmable timing (high/middle) for optimized motor efficiency and response
- Durable 3.5mm banana connectors on motor outputs for secure connections
- Integrated special firmware for fast throttle response and superior flight performance
- Genuine ReadytoSky product with fast shipping across India from Zbotic
Applications and Use Cases
- Racing quadcopters requiring rapid throttle response and precise control
- Aerial photography and videography drones needing smooth motor operation
- FPV multi-rotor builds where weight and efficiency matter
- DIY drone prototypes and experimental UAV platforms
- Educational robotics projects involving multi-rotor speed control
How to Use 40A 2-6S ESC 3.5mm Banana connector
Mount the ESC close to your motor, solder the battery leads to your chosen LiPo pack (2-6S), and plug the 3.5mm banana connectors into your motor. Connect the signal wires to your flight controller’s throttle channel, then power up and calibrate throttle range. Use a compatible programming card or your controller’s programming protocol to set high or middle timing, perform a bench test of throttle response, and secure the ESC in your frame.
Why Buy from Zbotic?
- Genuine Products: All items sourced from authorized distributors
- Fast Shipping: Orders ship within 24 hours with tracking (non backordered products)
- Free Shipping: Free delivery on qualifying orders
- COD Available: Cash on Delivery, UPI, cards, net banking
- Technical Support: Expert help for setup and troubleshooting
- Easy Returns: Hassle-free replacement for defective products
Frequently Asked Questions
How do I program the timing settings on this ESC?
You can adjust the timing between high and middle using a ReadytoSky-compatible programming card or via throttle-based programming on your flight controller. Follow the ESC manual steps: enter programming mode, select timing, and confirm.
Can I use this ESC with a 6S LiPo battery?
Yes. The 40A 2-6S ESC is rated for 2S up to 6S LiPo packs, allowing you to run higher-voltage setups safely within its specified limits.
What connectors are provided for motor and battery connections?
The ESC comes equipped with 3.5mm banana connectors on the motor output side and heavy-gauge power leads for the battery input. A standard signal cable is included for throttle connection to your receiver or flight controller.
How to Set Up Pixhawk Flight Controller Step-by-Step
Getting your Pixhawk setup right the first time saves hours of frustration and prevents crashes. The Pixhawk family...
Read More →
Drone Motor KV Rating Calculator and Selection Guide
Understanding the drone motor KV rating and how to calculate the right motor for your build is fundamental...
Read More →
Long Range Cruiser Drone: 7-Inch Build for Exploration
Table of Contents Understanding Long Range Cruiser Drone Key Components and Requirements Step-by-Step Setup Guide Configuration and Optimisation...
Read More →Technical Specifications
| Current Rating | 40A |
|---|---|
| Cell Configuration | 6S |
| Size | 3.5mm |
| Connector Type | Banana |
| SKU | AI5807 |
| Weight | 0.03 kg |
| Availability | Out of Stock |
Applications & Use Cases
The 40A 2-6S ESC 3.5mm Banana connector is a versatile (esc) drone speed controller used across a wide range of applications including brushless motor speed control, FPV drone builds, multirotor platforms, and RC aircraft.
Common use cases:
- Controlling motor speed in a quadcopter
- Replacing a burnt ESC after a short
- Upgrading to BLHeli_32 for smoother throttle response
This product is ideal for drone builders and RC enthusiasts.
Technical Tip: Choose ESC amperage 20% above your motor's max draw. DShot600 protocol recommended for modern builds.
Shipping & Delivery
- Free shipping on orders above ₹999 across India
- Dispatched within 1-3 business days
- Expected delivery: 3-7 business days depending on location
- Secure packaging to ensure safe transit of electronic components
Harsh Solanki (verified owner) –
Okay 40A 2-6S ESC 3.5mm Banana connector. Gets the job done for my basic drone project. Nothing exceptional.
Vikram Ghosh (verified owner) –
My 5th order from Zbotic. This 40A 2-6S ESC 3.5mm Banana connector is excellent as always. Totally reliable store.
Sarthak Iyer (verified owner) –
This 40A 2-6S ESC 3.5mm Banana connector is value for money. Comparing with other brands, Zbotic offers the best deal.
Lokesh Mittal (verified owner) –
Nice 40A 2-6S ESC 3.5mm Banana connector, does the job. Delivery took a couple of extra days but product is solid.
Raghav Saini –
My 5th order from Zbotic. This 40A 2-6S ESC 3.5mm Banana connector is excellent as always. Totally reliable store.
Simran Chauhan (verified owner) –
Using this 40A 2-6S ESC 3.5mm Banana connector in my hexacopter. Smooth operation and excellent thrust.
Sunil Iyer –
My 5th order from Zbotic. This 40A 2-6S ESC 3.5mm Banana connector is excellent as always. Totally reliable store.
Varun Bhandari (verified owner) –
This 40A 2-6S ESC 3.5mm Banana connector exceeded my expectations. Installed it yesterday and took a successful test flight today.
Mayank Deshpande (verified owner) –
Very impressed with this 40A 2-6S ESC 3.5mm Banana connector. My drone’s performance improved noticeably.
Tarun Sharma (verified owner) –
This 40A 2-6S ESC 3.5mm Banana connector exceeded my expectations. Installed it yesterday and took a successful test flight today.
Divyansh Srivastava (verified owner) –
Received the 40A 2-6S ESC 3.5mm Banana connector in great condition. Testing done, everything works perfectly.
Piyush Bose –
Good 40A 2-6S ESC 3.5mm Banana connector. Works well for my drone build. Packaging could be slightly better.
Akash Deshpande (verified owner) –
My 5th order from Zbotic. This 40A 2-6S ESC 3.5mm Banana connector is excellent as always. Totally reliable store.
Akshat Bhandari –
Solid 40A 2-6S ESC 3.5mm Banana connector. Not the absolute best but excellent value for the price point.
Atharv Patil (verified owner) –
Pretty good 40A 2-6S ESC 3.5mm Banana connector. Works as expected for my drone project. Would buy again.
Akshat Tandon (verified owner) –
Excellent 40A 2-6S ESC 3.5mm Banana connector! Perfect for my quadcopter build. Arrived well packed and works flawlessly.
Mukesh Negi (verified owner) –
This 40A 2-6S ESC 3.5mm Banana connector is value for money. Comparing with other brands, Zbotic offers the best deal.
Kavya Thakur (verified owner) –
This 40A 2-6S ESC 3.5mm Banana connector is exactly what I needed for my drone. Works perfectly, very reliable.