HC-05 Bluetooth Module Not Pairing: Causes & Step-by-Step Fix

The HC-05 Bluetooth module not pairing is one of the most common frustrations for Arduino beginners and experienced makers alike. You have wired everything up, uploaded your code, opened the Bluetooth settings on your phone — and nothing. Or it shows up briefly and then disappears. Or it pairs but immediately disconnects. This troubleshooting guide covers every known cause of HC-05 pairing failures and provides a systematic, step-by-step fix that resolves the problem in over 95% of cases. Whether you are working with an Arduino Uno, Nano, or Mega, this guide has you covered.

How the HC-05 Module Works

The HC-05 is a Bluetooth 2.0 Classic module (SPP — Serial Port Profile) that creates a wireless serial link between two devices. It operates at 2.4GHz and communicates with Arduino via UART (TX/RX). The module has two operating modes:

• Data Mode (normal): The module is discoverable, accepts pairing requests, and transparently relays serial data. The LED blinks rapidly (every ~2 seconds) when not paired, and stays on steadily when connected.
• AT Command Mode: Entered by holding the KEY/EN pin HIGH before powering on (or pressing the small onboard button before power-on on most modules). The LED blinks slowly (every ~1 second). In this mode, you send AT commands at 38400 baud to query and configure the module.

The default HC-05 pairing PIN is 1234 (some modules use 0000). The default baud rate for data mode is 9600 (for some modules it is 38400 — check with AT+UART?).

0.96 Inch I2C OLED LCD Module (White, SSD1306)

Add an OLED display to your HC-05 project to show Bluetooth connection status, sensor data, and debug information in real time.

View on Zbotic

Step 1: Power Supply Verification

Power problems are responsible for at least 30% of HC-05 pairing failures. The HC-05 module requires 3.3V on its VCC pin (the breakout boards with a 6-pin header include a 3.3V regulator and can accept 5V on the VCC pin — but the bare module cannot). Current draw can reach 40mA during active transmission.

Common Power Mistakes

• Powering from Arduino 3.3V pin: The Arduino Uno’s 3.3V regulator is limited to 50mA total. Combined with other 3.3V loads, this causes voltage sag and connection drops. Use a dedicated 3.3V regulator (AMS1117-3.3) for the HC-05 if you are not using a breakout board with an onboard regulator.
• Long jumper wires adding resistance: High-resistance connections cause voltage drop under load. Use short, direct jumper wires.
• Shared GND not connected: The HC-05 and Arduino must share a common GND.

Test: Measure voltage at the HC-05 VCC pin with a multimeter while the module is powered on. It should read 3.3V (±0.1V). If it reads below 3.0V, fix your power supply first.

Step 2: LED Blink Pattern Diagnostics

The HC-05’s onboard LED is your most immediate diagnostic tool:

If you see rapid blinking but your phone cannot find the module, proceed to Step 3 to check AT command settings. If the LED is off despite power, the module may be faulty or you have a wiring error.

Step 3: Enter AT Command Mode & Verify Settings

AT Command mode lets you verify and fix the module’s internal settings. This is the most powerful diagnostic step.

How to Enter AT Mode

1. Power OFF the HC-05 and Arduino
2. Hold the HC-05’s KEY/EN button (or connect KEY pin to 3.3V/5V)
3. Power ON while keeping KEY held
4. LED should now blink slowly (~1 per second) — you are in AT mode
5. Open Arduino IDE Serial Monitor: set baud to 38400, line ending to Both NL & CR

Essential AT Commands

AT                    → Should reply OK (confirms AT mode is working)
AT+VERSION?           → Returns firmware version (e.g., 3.0-20170601)
AT+NAME?              → Returns module name (default: HC-05)
AT+ADDR?              → Returns Bluetooth MAC address
AT+PSWD?             → Returns current PIN (default: 1234)
AT+UART?             → Returns baud,stopbits,parity (e.g., 9600,0,0)
AT+ROLE?             → Returns role (0=Slave, 1=Master)
AT+STATE?            → Returns current state (INITIALIZED, PAIRABLE, etc.)

Fix Commands

AT+NAME=ZBOTIC_BT     → Rename module (visible in phone Bluetooth scan)
AT+PSWD=1234          → Reset PIN to 1234
AT+UART=9600,0,0      → Set baud rate to 9600 (match your Arduino sketch)
AT+ROLE=0             → Set as Slave (must be 0 for phone-to-Arduino pairing)
AT+RESET              → Restart module in data mode

Critical check: Verify AT+ROLE? returns 0. If the role is 1 (Master), the module will not accept pairing from your phone — it will try to connect TO another device. This is the single most common misconfiguration.

0.96 Inch SPI OLED LCD Module (Blue, SSD1306)

SPI OLED display for showing Bluetooth debug output and sensor readings in Arduino Bluetooth projects.

View on Zbotic

Step 4: Fix Android Pairing Issues

Android Bluetooth pairing issues with HC-05 are distinct from hardware problems. Here is a reliable procedure:

Standard Android Pairing Procedure

1. Make sure HC-05 is in Data Mode (rapid LED blink — NOT AT mode)
2. On Android, go to Settings → Connected Devices → Bluetooth
3. Tap Scan or Pair new device — you should see "HC-05" (or whatever name you set)
4. Tap the device name — you will be prompted for a PIN
5. Enter 1234 (or 0000 if 1234 fails)
6. Tap OK — the status should change to "Paired"

If HC-05 Does Not Appear in Android Scan

• Toggle Bluetooth OFF and ON on your phone (clears the scan cache)
• Verify HC-05 LED is blinking rapidly (not slow AT mode blink)
• Confirm the HC-05 is not already paired to another device (another phone, laptop) — a paired HC-05 may not be discoverable to additional devices simultaneously
• On newer Android (12+), make sure you have granted "Nearby devices" permission to your Bluetooth app

If Pairing Immediately Fails or Disconnects

• Forget/unpair the device on Android first, then try again fresh
• Reset the HC-05 PIN via AT command: AT+PSWD=1234
• Some Android 10+ phones have issues with older Bluetooth 2.0 SPP devices — use a dedicated Bluetooth Terminal app (like "Serial Bluetooth Terminal" by Kai Morich) instead of the generic Bluetooth settings pairing

Step 5: Correct Wiring & Voltage Level

Incorrect wiring is another top cause of HC-05 failures. The HC-05’s TX/RX pins operate at 3.3V logic, while Arduino Uno/Nano TX/RX are at 5V logic. Connecting 5V directly to HC-05 RX can damage the module over time.

Correct Wiring (Arduino Uno to HC-05 Breakout Board)

Critical: Do NOT connect HC-05 TXD and RXD to Arduino hardware UART pins 0 and 1 while also using USB Serial Monitor — they share the same UART on Uno/Nano and will conflict. Use SoftwareSerial on pins D10/D11 for HC-05.

Step 6: Matching Baud Rate in Code

A mismatch between the HC-05’s configured baud rate and your Arduino sketch’s SoftwareSerial baud rate causes garbled data and apparent "connection" failures where the module pairs but no data flows.

#include <SoftwareSerial.h>

// HC-05 TXD → Arduino D10, HC-05 RXD → Arduino D11 (via voltage divider)
SoftwareSerial bluetooth(10, 11); // RX, TX

void setup() {
  Serial.begin(9600);      // USB Serial Monitor
  bluetooth.begin(9600);   // MUST match AT+UART? setting on HC-05
  Serial.println("HC-05 ready. Waiting for Bluetooth connection...");
}

void loop() {
  // Forward data from Bluetooth to Serial Monitor
  if (bluetooth.available()) {
    char c = bluetooth.read();
    Serial.write(c);
  }
  
  // Forward data from Serial Monitor to Bluetooth
  if (Serial.available()) {
    char c = Serial.read();
    bluetooth.write(c);
  }
}

This is a transparent bridge sketch — it passes data between your phone’s Bluetooth terminal app and the Arduino Serial Monitor. Use it to verify your HC-05 is working before adding application logic.

1 Channel 12V 30A Relay Module with Optocoupler

Control high-power devices via Bluetooth using this optocoupler-isolated relay — a natural next step after getting HC-05 working with Arduino.

View on Zbotic

1 Channel 12V Solid State Relay Module (SSR, High Level)

Silent solid-state relay for Bluetooth-controlled AC switching projects — no mechanical noise, longer lifespan than traditional relays.

View on Zbotic

0.96 Inch SPI OLED LCD Module 7-pin (White, SSD1306)

7-pin SPI OLED display with CS pin — ideal for showing Bluetooth status, commands received, and sensor data in HC-05 Arduino projects.

View on Zbotic

Frequently Asked Questions