Looking for Pixhawk 2.4.8 Combo Kit? PIXHAWK 2.4.8 Combo Kit is available at Zbotic with fast shipping across India.
Product Description
This PIXHAWK 2.4.8 Full Combo Kit consists of all in one required product for the drone flight controller. find all product included in this kit at below package includes.
PIXHAWK PX4 2.4.8 Flight Controller is a high-performance autopilot-on-module suitable for fixed-wing, multi-rotors, helicopters, cars, boats, and any other robotic platform that can move. It is targeted towards high-end research, amateur and industry need, and combines the functionality of the PX4FMU PX4IO.
A new generation Ublox GPS NEO-M8N, with low power consumption and high precision, the ultimate accuracy is 0.6 meters, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy; support GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol, and mode or more.
The GPS Folding Antenna Base mount comes will a laser-cut adhesive pad to quickly attached your GPS module, while the mount itself can be fixed to your craft using the base plate M3 hole, or the cross slides.
Note: Product image may vary from the actual product.
Specifications and Features:
Pixhawk V2.4.8 Flight board:
- The advanced 32-bit ARM CortexM4 high-performance processors can run NuttX RTOS real-time operating system.
- 14 PWM / servo output.
- Bus interface (UART, I2C, SPI, CAN).
- The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe.
- Provide automatic and manual modes.
- Provide redundant power input and failover.
- Multicolor LED lights.
- Provide a multi-tone buzzer Interface.
- Micro SD recording flight data.
Processor:
-
32bit STM32F427 Cortex M4 core with FPU.
-
168 MHz.
-
128 KB RAM.
-
2 MB Flash.
-
32-bit STM32F103 failsafe co-processor.
Sensors:
-
ST Micro L3GD20H 16 bit gyroscope.
-
ST Micro X4HBA 303H 14-bit accelerometer/magnetometer.
-
Invensense MPU 6000 3-axis accelerometer/gyroscope.
-
MEAS MS5607 barometer.
Interfaces:
-
5x UART (serial ports), one high-power capable, 2x with HW flow control.
-
2x CAN (one with an internal 3.3V transceiver, one on expansion connector).
-
Spektrum DSM / DSM2 / DSM-X® Satellite compatible input.
-
Futaba S.BUS® compatible input and output.
-
PPM sum signal input.
-
RSSI (PWM or voltage) input.
-
I2C.
-
SPI.
-
3.3 and 6.6V ADC inputs.
-
Internal micro USB port and external micro USB port extension.
PIXHAWK PPM Encoder Module:
- Support the input channels: 8.
- Output: PPM SUM × 1 / MUX × 1.
Glass Fiber Flight Controller Anti-vibration/Shock absorber Set:
- Color: Black
- Material: Glass-fiber
- Suit for the different open-source flight controllers, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4
NEO-M8N GPS Module:
- Receiver type 72-channel Ublox M8 engine.
- GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1.
- SBAS L1 C/A: WAAS, EGNOS, MSAS.
- Galileo-ready E1B/C (NEO-M8N).
- Nav. update rate1 Single GNSS: up to 18 HZ.
- Concurrent GNSS: up to 10 Hz.
- Position accuracy2 2.0 m CEP.
- Acquisition2 Cold start: 26 s.
- Aided starts: 2 s.
- Reacquisition: 1.5 s.
- Sensitivity2 Tracking & Nav: –167 dBm.
- Cold start: –148 dBm.
- Hot starts: –156 dBm.
- Assistance AssistNow GNSS Online.
- Assist Now GNSS Offline (up to 35 days)3.
- Assist Now Autonomous (up to 6 days).
- OMA SUPL & 3GPP compliant
- Oscillator TCXO (NEO-M8N/Q).
- Crystal (NEO-M8M).
- RTC crystal Built-In.
- Noise figure On-chip LNA (NEO-M8M). Extra LNA for.
- lowest noise figure (NEO-M8N/Q).
- Anti-jamming Active CW detection and removal.
- An extra onboard SAW bandpass filter (NEO-M8N/Q).
- Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N).
- Supported antennas Active and passive.
- Odometer Travelled distance.
- Data-logger For position, velocity, and time (NEO-M8N).
GPS Folding Base Antenna set:
- Material: CNC Aluminum alloy, carbon glass fiber rod
- Mounting rod diameter: 4mm
- length of rod: 14 cm.
- GPS plate diameter: 40 mm.
- Base plate diameter: 35 mm
- Mounting hole spacing: 16-35mm
- Weight: 20g
- Colour: Anodised black
- Note: Adhesive Pad is not included.
APM 2.5.2/2.6/2.8 Pixhawk Power Module V1.0:
- Max input voltage: 28V
- Max current sensing: 90A
- Voltage and current measurement configured for 5V ADC
- Switching regulator outputs 5.3V and 3A max
- 6-pos DF13 cable plugs directly to APM 2.5’s ‘PM’ connector
- Support 6S battery.
Package Includes:
1 x Pixhawk V2.4.8 Flight board with Original Shell.
1 x 4GB TF card(IO firmware has written).
3 x Connecting Cables.
1 x Pixhawk PPM Encoder Module.
1x JR plug 10P input end of the cable 100mm.
1 x JR plug 4P output end of the cable 100mm.
1 x Glass Fiber Flight Controller Anti-vibration/Shock absorber Set.
1x NEO-M8N GPS Module with translucent Shell.
2 x cables (APM/PIX).
1 x GPS Folding Base Antenna set.
1 x APM 2.5.2/2.6/2.8 Pixhawk Power Module.
1 x I2C Splitter with Cable
1 x OSD OLED Display
PIXHAWK 2.4.8 Combo Kit Overview
The PIXHAWK 2.4.8 Combo Kit is a complete autopilot solution combining the PX4 2.4.8 flight controller and Ublox NEO-M8N GPS module for precise navigation. Designed for drones, fixed-wing aircraft, helicopters, cars and boats, it delivers real-time control via a 32-bit ARM Cortex-M4 processor running NuttX RTOS.
Key Features of PIXHAWK 2.4.8 Combo Kit
- Genuine Pixhawk 2.4.8 kit from authorized distributors, fast shipping across India via Zbotic
- 32-bit ARM Cortex-M4 high-performance CPU with NuttX real-time OS
- 14 PWM/servo outputs plus UART, I2C, SPI and CAN bus interfaces
- Integrated backup power module and failsafe controller with redundant power input
- Multicolor LED status indicators and multi-tone buzzer interface
- Onboard micro SD slot for flight data logging and new-generation Ublox NEO-M8N GPS (0.6–0.9 m accuracy)
Applications and Use Cases
- Autonomous multicopter mapping and photogrammetry missions
- Fixed-wing UAV aerial surveys and waypoint navigation
- Helicopter flight stabilization and precision agriculture spraying
- Ground rover and car robotics for research and prototyping
- Autopilot control for RC boats and marine exploration
- Industrial R&D platforms requiring redundant power and failsafe
How to Use PIXHAWK 2.4.8 Combo Kit
Mount the PX4 flight controller securely on your frame, connect the power module and safety switch, then wire ESCs, servos and sensors to the 14 PWM outputs and bus ports. Attach the Ublox NEO-M8N GPS module with its mounting bracket away from magnetic interference. Insert a micro SD card for data logging, then use Mission Planner or QGroundControl to upload firmware, calibrate sensors, configure flight modes and test failsafe settings before the first flight.
Why Buy from Zbotic?
- Genuine Products: All items sourced from authorized distributors
- Fast Shipping: Orders ship within 24 hours with tracking (non backordered products)
- Free Shipping: Free delivery on qualifying orders
- COD Available: Cash on Delivery, UPI, cards, net banking
- Technical Support: Expert help for setup and troubleshooting
- Easy Returns: Hassle-free replacement for defective products
Frequently Asked Questions
What platforms are supported by the PIXHAWK 2.4.8 Combo Kit?
This kit supports multi-rotors, fixed-wing aircraft, helicopters, ground rovers, cars and boats. Its versatile PX4 FMU and PX4IO integration enables control of almost any robotic platform.
How accurate is the included Ublox NEO-M8N GPS module?
The Ublox NEO-M8N GPS in this combo provides positioning accuracy down to 0.6 meters under optimal conditions (typically around 0.9 meters in field use), ensuring precise waypoint navigation.
How do I set up the failsafe and backup power features?
Use your ground station software (Mission Planner or QGroundControl) to configure voltage and signal-loss thresholds. The integrated backup power module and controller will automatically switch to the secondary input if the main supply drops below your defined limits.
Indian Airspace Zones: Where Can You Fly Your Drone
Understanding Indian airspace zones for drone flying is fundamental for every drone pilot, whether you are flying recreationally...
Read More →
Drone Winch System: Pick and Place Payload Delivery UAV
Drone Winch System: Pick and Place Payload Delivery UAV The idea of drones that can autonomously pick up...
Read More →
DIY Drone Payload Release Mechanism: Step-by-Step Build
Table of ContentsIntroduction: Why Add a Payload Release to Your Drone?Types of Payload Release MechanismsComponents RequiredBuilding a Servo-Based...
Read More →Technical Specifications
| Brand | Pixhawk |
|---|---|
| SKU | AI1500 |
| Weight | 0.39 kg |
| Availability | Out of Stock |
Applications & Use Cases
The PIXHAWK 2.4.8 Combo Kit is a versatile drone kit used across a wide range of applications including electronics projects, DIY builds, prototyping, and educational experiments.
Common use cases:
- Integrating into a custom electronics project
- Learning and experimenting with circuits
- Replacing or upgrading components in existing setups
This product is ideal for electronics enthusiasts, engineers, and students.
Technical Tip: Always verify voltage and current requirements before connecting to your circuit. Check datasheets for detailed specifications and pin configurations.
Shipping & Delivery
- Free shipping on orders above ₹999 across India
- Dispatched within 1-3 business days
- Expected delivery: 3-7 business days depending on location
- Secure packaging to ensure safe transit of electronic components
- Genuine Pixhawk product sourced from authorized channels
