New Arrivals

300W 10A DC-DC Step-down Buck Converter Adjustable Constant Voltage Module

277.0 ( +GST 18% )
QUICK OVERVIEW
  • Input Supply voltage (V) : 7 ~ 40
  • Output voltage (V) : Continuously adjustable (1.25 ~ 35)
  • Output Current (A) : 8A (10A maximum)
  • Conversion efficiency: : 95%
  • Operating frequency (KHz) : 300
  • No-load current : Typical 20mA
  • Load regulation : 1%
  • Voltage Regulation: 1%

ESP WROOM 32 MCU Development Module – 30 Pin CH9102

361.0 ( +GST 18% )
QUICKOVERVIEW
  • Model: ESP WROOM 32 MCU
  • Processor: Single or Dual core Tensilica Xtensa 32-bit LX6
  • Operating voltage (v): 2.3 ~ 3.6
  • Operating current (mA): 80
  • Small volume, easily embedded to other products
  • Strong function with support LWIP Protocol, Freertos

GY-302 BH1750 Light Intensity Module

84.0 ( +GST 18% )
QUICKOVERVIEW
  • High precision determination accurate to 1 Lu for different lights
  • Operating Voltage: 3-5VDC
  • Built-in 16bit A/D converter
  • I2C interface

LM35DZ

37.0 ( +GST 18% )
QUICKOVERVIEW • Suitable for Remote Applications • Low-Cost Due to Wafer-Level Trimming • Operates From 4 V to 30 V • Less Than 60-μA Current Drain • Low Self-Heating, 0.08°C in Still Air • Non-Linearity Only ±¼°C Typical

PCT-223-3 Stationary Type Quick Connection Terminal

47.0 ( +GST 18% )
QUICK OVERVIEW
  • Rated voltage: 600V
  • Rated current: 32A
  • Number of poles: 3
  • Wire section : 0.08~4.0 mm2
  • Number of Clamps:6

PCT-223-5(SPL-5) Quick Connection Terminal

45.0 ( +GST 18% )
QUICKOVERVIEW
  • Rated voltage: 600V
  • Rated current: 32A
  • Number of poles: 5
  • Wire section : 0.08~4.0 mm2
  • No of Clamps:10

PCT-224(SPL-4) Quick Connection Terminal

39.0 ( +GST 18% )
QUICKOVERVIEW
  • Model: PCT-224(SPL-4)
  • Rated Voltage:400 V
  • Rated Current:32 A
  • Color:Gray+orange

Items On Sale

12V 4010 Cooling Fan for RPI

52.0 ( +GST 18% )
QUICK OVERVIEW
  • Perfectly fit on the extruder
  • Noiseless Performance
  • Very low Current consumption
  •  Easy to install and connect.

12V-2A DC Adapter With LED (Dual Pin DC)

121.0 ( +GST 18% )
QUICK OVERVIEW
  • Color : Black
  • Usage/Application : Electronic Instruments
  • Material : ABS Plastic
  • Type : Adaptor
  • Output Current : 2 Amp
  • Input Frequency : Range 50-60 Hz
  • Number Of Pins : 3 Pin
  • Output Voltage : 12 V
  • Input Voltage Range : 100-240V

15 CM 26AWG Servo Lead Extension (JR) Cable-1Pcs

46.0 ( +GST 18% )
QUICK OVERVIEW
  • High-Quality cable
  • One male and one female connector.
  • Quality wire and connectors used.
  • Great for larger planes with servos that experience high loads.
  • Wire Length: 150mm

150 RPM Single Shaft L- Shaped BO Motor

56.0 ( +GST 18% )
QUICK OVERVIEW
  • Shaft length: 7 mm
  • Motor Design: L-Shaped
  • Shaft Diameter: 5.5 mm
  • Size: 55 x 48 x 23 mm.
  • Operating Voltage: 3 to 12V
  • Current (without loading): 40-180mA
  • RPM: 150 rpm
  • Output Torque: 0.8 kg cm.

16×2 (1602) LCD Keypad Shield – Blue Backlight for Arduino

207.0 ( +GST 18% )
QUICK OVERVIEW
  • Blue Backlight with white words
  • uses 4 Bit Arduino LCD Library
  • Left, Right, Up, Down and Select buttons
  • Screen contrast adjustment
  • Arduino Reset button
  • Operating Voltage is 5V

2 Channel Tilt Sensor Module

155.0 ( +GST 18% )
QUICK OVERVIEW
  • Operating voltage 3.3V-12V
  • A fixed bolt hole for easy installation
  • Wide voltage LM393 comparator
  • Maximum output current: 15mA
  • Can work on low voltages
 

28BYJ-48 5V Stepper Motor

65.0 ( +GST 18% )
QUICK OVERVIEW
  • Rated voltage: 5V DC
  • Reduction Ratio: 64:1
  • Step Angle: 5.625° /64
  • Frequency: 100Hz
  • Self-positioning Torque: >34.3mN.m
  • Friction torque: 600-1200 gf.cm
  • Pull in torque: 300 gf.cm

3 Pin Screw Type PCB Terminal Block – 5mm Pitch (Pack of 5)

23.0 ( +GST 18% )
QUICK OVERVIEW
  • 3 Pin Terminal Block
  • Rated Voltage: 300V
  • Rated Current: 10A
  • Pitch: 5.08mm

3 Series 40A 18650 Lithium Battery Protection Board 11.1V 12.6V with Balance for Drill Motor Lipo Cell Module

160.0 ( +GST 18% )
QUICK OVERVIEW
  • 3S 11.1V 12.6V 40A 18650 lithium battery protection board (comes with recovery function-AUTO Recovery)
  • Application: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650.26650, a polymer lithium battery)
  • Continuous discharge current (upper limit): 40A (if the cooling environment is not good, please reduce the load current use)
  • Continuous charge current (upper limit): 20A

3.3V/5V MB102 Breadboard Power Supply Module

59.0 ( +GST 18% )
QUICK OVERVIEW
  • Breadboard power supply module, compatible with 5V, 3.3V.
  • Apply to MB102 breadboard
  • Input voltage: 6.5-12 V (DC) or USB power supply
  • Output voltage: 3.3V/5V can switch over
  • Maximum output current: <700 ma
  • Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V
  • On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use.

3.7V Lithium Battery Protection Board for Polymer 18650 Bonding Pad (can Spot/Weld) 3A Overcurrent Value

20.0 ( +GST 18% )
QUICK OVERVIEW
  • Overcharge voltage: 4.25±0.05V
  • Overcharge release voltage:4.23±0.05V
  • Over discharge voltage:2.54±0.1V
  • Maximal continuous charging current: 2A

315MHz RF Transmitter Receiver Module

58.0 ( +GST 18% )
QUICK OVERVIEW
  • Operating voltage: 5V.
  • Quiescent Current: 4mA.
  • Receiving frequency: 315MHz.
  • Receiver sensitivity: -105 dB.
  • Communication Distance (m): 20 ~ 200 meter.

4 IR Sensor Array Module

93.0 ( +GST 18% )
  • Working voltage (V): 3.3 ~ 5
  • Working current (A): Above 1A
  • Operating Temperature (℃): -10 ~ +50
  • Mounting hole: M3
  • Detection range: 1mm ~ 20 cm adjustable.

4 Road/Channel Relay Module (with light coupling) 12V

150.0 ( +GST 18% )
QUICK OVERVIEW
  • Operating Voltage: 12V DC
  • Equipped with high-current relay [email protected] / [email protected]
  • It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc.
  • High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
  • Freewheeling diode to protect your microcontroller
  • Input Signal Pin connected to Burg stick for easy accessibility
  • LED Status indicators to indicate the relay ON/OFF status
  • Mounting holes provided
 

400 Points Solderless Breadboard

38.0 ( +GST 18% )
QUICK OVERVIEW
  • Type: Plug-in breadboard
  • Size: 3.3 x 0.3 inches
  • Total 400 tie points
  • 2 power buses
  • 400 tie in points
  • 0.1" space
  • 10 rows

4×4 Matrix Keypad Membrane Switch

32.0 ( +GST 18% )
QUICK OVERVIEW
  • 4 x 4 Matrix Membrane Keypad
  • 8 pin connector
  • Adhesive mounting (sticker on the back side)
  • Operation Temperature: 0 to 60 centigrade
  • Humidity: 40 centigrade, 90%-95%, 240 hours
  • Flexible Circuit Length: Approx. 3.3 inch / 83 mm

5 Pin Relimate Cable Connector Female – 2.54mm Pitch (Pack of 2)

7.7 ( +GST 18% )
QUICK OVERVIEW
  • Connector Type: JST-VH
  • Number of Pin: 5
  • Variant: Female
  • Pitch: 2.54mm
  • Wire Length: 25cm

5A Range Current Sensor Module ACS712

91.0 ( +GST 18% )
QUICK OVERVIEW
  • Low-noise analog signal path.
  • Device bandwidth is set via the new FILTER pin.
  • 5 µs output rise time in response to step input current.
  • Small footprint, low-profile SOIC8 package.
  • 1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
 

5V Active Electromagnetic Buzzer (Pack of 5)

59.0 ( +GST 18% )
  • Input Voltage(Max.) : 5V
  • Resistance: 90 Ω
  • Resonance Frequency: 2048 Hz
  • Sound pressure(dB(A)/10cm)min.: 80
  • Body Size : 12 x 9.5mm
  • Pin Pitch: 6mm
  • External Material: Plastic;
  • Color: Black

5V Double Channel Relay Module (Made In India)

30.0 ( +GST 18% )
QUICK OVERVIEW
  • High current relay, AC250V 10A, DC5V 10A
  • 2 LEDs to indicate when relays are on
  • Works with logic level signals from 3.3V or 5V devices
  • Opto isolation circuitry

65mm Robot Wheel for BO Motors (Yellow)

27.0 ( +GST 18% )
QUICK OVERVIEW
  • Loading Capacity (Kg): 2.5
  • D hole For BO Motor: 6 mm
  • Weight (gm): 34
  • Wheel Diameter(mm): 65 mm
  • ColorBlack (Tyre): Yellow (Rim)
  • Wheel Width 27 mm
  • Body Material Plastic
  • Grip Material Rubber
  • Center Shaft Hole Diameter
  • 5.4mm-(round side) and 3.5mm-(flat side)

74LS47 BCD to 7-Segment Decoder/Driver IC (7447 IC) DIP-16 Package

23.0 ( +GST 18% )
QUICK OVERVIEW
  • Lamp Test input
  • Supply Voltage (VCC); 7V
  • Input Voltage (VI): 7V
  • Operating free-air temperature range: 0°C to +70°C
  • Storage temperature range: –65°C to +150°C

8 Pin Relimate Cable Connector Female – 2.54mm Pitch (Pack of 2)

10.4 ( +GST 18% )
QUICK OVERVIEW
  • Connector  Type: JST-VH
  • Number of Pins: 8
  • Variant: Female
  • Wire Length: 25cm
  • Pitch: 2.54mm

A03B 1 Road 5V Low Level Solid State Relay Module with Fuse SSR 250V 2A Fuse

110.0 ( +GST 18% )
QUICK OVERVIEW
  • Trigger voltage: 5VDC
  • Trigger current: 2mA
  • Switching Voltage: [email protected]
  • Triggering: Low-level
 

A2212 1000KV BLDC Brushless DC Motor for Drone

325.0 ( +GST 18% )
QUICK OVERVIEW
  • Motor KV: 1000
  • Current Capacity: 12A/60S
  • LiPO Batteries: 2S-3S
  • Max. Efficiency Current: 4-10A
  • Shaft Diameter: 3.17 mm
  • Prop Adapter is quality tested before shipping to customers.

Ai-Thinker LoRa Series Ra-02 Spread Spectrum Wireless Module

325.0 ( +GST 18% )
  • Manufacturer: Ai-Thinker
  • LoRa  Spread Spectrum modulation technology
  • Constant RF power output at + 20dBm-100mW voltage change
  • High sensitivity: down to -148dBm
  • Half-duplex SPI communication
  • Programmable bit rates up to 300kbps
  • Supports FSK, GFSK, MSK, GMSK, LoRa  and OOK modulation modes
 

Alligator Clips Electrical DIY Test Leads 10pcs of Double-ended Crocodile Clips Roach Clip

48.0 ( +GST 18% )
QUICK OVERVIEW
  • Colour: Red, Green, Yellow, White, and Black, etc.
  • Cable length: 45 cm.
  • Net weight: 82 gm.
  • They are very useful for connecting components to wires.
  • It is insulation covered clips connected to the wire from both ends.

ATMEGA16 ATmega 32 ISP AVR Minimum Development System Board Module

208.0 ( +GST 18% )
QUICK OVERVIEW
  • 32 I/O pin all the leads.
  • Classic ATmega16 minimum system, eliminating the hassle of soldering.
  • Support chips: ATmega16/ATmega32 and chip which pin-compatible.
  • Power supply: power adapter or external expansion pin power supply (not support ISP download interface power supply)
  • DC-005 Power Block (supporting the transposon is 5.5*2.1mm).
  • Reset: Power-on-reset and reset button.
  • Power LED (D1) and the program run indicator (D2).
  • Standard ISP download interface.

ATMEGA16U2 Arduino Mega 2560 R3 Improved Version CH340G Board

1,070.0 ( +GST 18% )
QUICK OVERVIEW
  • Microcontroller CH340
  • Operating Voltage 5V
  • Input Voltage (recommended) 7-12V
  • Input Voltage (limits) 6-20V
  • Digital I/O Pins 54 (of which 15 provide PWM output)
  • Analog Input Pins 16
  • DC Current per I/O Pin 40 mA
  • Dimensions : 111 x 54 x 12 (LxWxH) mm.

BC547 NPN 100mA Transistor TO-92 (Pack of 10)

12.0 ( +GST 18% )
QUICK OVERVIEW
  • Package/Case: TO-92-3
  • Transistor Polarity: NPN
  • Collector- Emitter Voltage VCEO Max: 45 V
  • Collector- Base Voltage VCBO: 50 V
  • Emitter- Base Voltage VEBO: 6 V

BC558 PNP Transistor ( Pack of 10)

13.1 ( +GST 18% )
QUICK OVERVIEW
  • Collector-Emitter Voltage: -30V
  • Collector-Base Voltage: -30V
  • Emitter-Base Voltage: -5V
  • Continuous Collector Current: 100mA
  • DC Current Gain (hFE): 110 to 800
  • Total Power Dissipation: 500mW
  • Storage and Operating Temperature Range: -65℃ to +150℃
  • Number of pins: 3
  • Package: TO-92
  • Mounting type: Through hole

BD140 PNP Bipolar Medium Power Transistor 80V 1.5A TO-126 Package (Pack of 10)

47.0 ( +GST 18% )
QUICK OVERVIEW
  • Collector-base Voltage: -80V
  • Collector Current: -1.5A
  • Transistor Polarity: PNP
  • Total Power Dissipation: 12.5W
  • Current Gain max. : 250
  • Package: T0-126

BMP280 Barometric Pressure and Altitude Sensor I2C/SPI Module

36.0 ( +GST 18% )
QUICK OVERVIEW
  • Operating Voltage: 1.71V to 3.6V  would typically be operated from 3.3V.
  • Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C).
  • Peak current: 1.12mA.
  • Operating Pressure: 300 hPa to 1100 hPa.
  • Accuracy between 700 to 900hPa and 25 to 40 deg. C : ±0.12hPa and ±1.0m.

BO Motor 150 RPM – Straight

47.0 ( +GST 18% )
QUICK OVERVIEW
  • Low density: lightweight, low inertia.
  • Capability to absorb shock and vibration as a result of elastic compliance.
  • Ability to operate with minimum or no lubrication, due to inherent lubricity.
  • The relatively low coefficient of friction.
  • Operating Voltage(VDC): 3~12
  • Shaft Length (mm): 8.5
  • Shaft Diameter (mm): 5.5 (Double D-type)
  • No Load Current: 40-180mA.
  • Rated Speed(After Reduction): 150 RPM
  • Rated Torque: 0.35 Kgcm

Capacitor Touch Dimmer Constant Voltage LED Stepless Dimming PWM Control Board

52.0 ( +GST 18% )
QUICK OVERVIEW
  • Operating Voltage Range : 2.4 – 4.5
  • Aperture (mm) : 16
  • Length (mm) :   39
  • Width (mm)  :        19
  • Height (mm) :  11
  • Weight (gm)  :  3

Counter Rotating Propeller 1045/1045R For Quadrotor-(Black)

48.0 ( +GST 18% )
QUICK OVERVIEW
  • Length: 10" (25.4 cm).
  • Pitch: 4.5 (11.43 cm).
  • Weight: 14 gm.
  • Shaft Diameter: 6 mm.
  • Total length: 10 inch / 254 mm.
 

CP2102 USB 2.0 to TTL UART Serial Convertor Module

146.0 ( +GST 18% )
QUICK OVERVIEW
  • Stable and reliable chipset CP2102.
  • USB specification 2.0 compliant with full-speed 12Mbps.
  • Standard USB type A male and TTL 6pin connector.
  • 6pins for 3.3V, RST, TXD, RXD, GND & 5V.
  • Baud rates: 300 bps to 1.5 Mbps

DC 12V-36V 500W Brushless Motor Controller Hall Balanced Car Driver Board

899.0 ( +GST 18% )
QUICK OVERVIEW
  • Operating Voltage: DC12-36V
  • Operating Current: <=15A
  • Drive Power: <=500W
  • Speed Voltage: 0.1V-5V
  • Operating Temperature: -40~85 degrees Celsius
  • Humidity: <=90%RH
  • Stall Protection: Yes

DS1302 Real Time Clock (RTC) Module

51.0 ( +GST 18% )
Quick Review :
  • Crystal 32.768KHz, matching capacitance 6pF
  • DS1302 8-pin SMD homemade chips
  • Seconds, Minutes, Hours, Day of Month, Day of Week, and Year

Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 Lipo Charger

93.0 ( +GST 18% )
QUICK OVERVIEW
  • 4-level LED lamp display power, not working state intelligent automatic shutdown.
  • Dual USB output ports.
  • Input port: MicroUSB (Andro).
  • Output port: USB.
  • Output parameters: 5V1A / 5V2A.

ESP8266 Adapter Plate Serial Wireless WiFi Module

20.0 ( +GST 18% )
QUICK OVERVIEW
  1. It features reserved land-pattern for the 3.3V regulator
  2. It has Pinouts on the top layer in black colour.
  3. Compatible with Latest ESP-12F ESP8266 Wifi Module
  4. It includes a 10K pull-up resistor populated on PCB.

Espressif ESP32-WROOM-32E 4M 

236.0 ( +GST 18% )
QUICK OVERVIEW
  • Frequency: 2.4 GHz to 2.5 GHz
  • Data rate: 150MBits/s.
  • Power output: 20dBm
  • Sensitivity -98dBm
  • Serial interfaces: ADC, GPIO, I²C, I²S, PWM, SDIO, SPI, UART
  • Antenna type: Integrated, conductor path
  • Memory size: 448kB ROM, 536kB SRAM

F450 4 Axis Quadcopter Frame Kit

650.0 ( +GST 18% )
QUICK OVERVIEW
  • Width: 450mm
  • Height: 55mm
  • Weight: 270g (w/out electronics)
  • Motor Mount Bolt Holes: 16/19mm

Flat 1034 Mobile Phone Vibrator Motor

18.3 ( +GST 18% )
QUICK OVERVIEW
  • Type: 1034
  • Rated Voltage(V): 3
  • Operating Voltage(VDC): 2.5 to 4
  • Operating Temperature (C): -20 to 60
  • Min. Rated Speed(RPM): 9000
  • Max. Rated Current(mA): 90
  • Max. Starting Current(mA): 120
  • Cable Length: 20 cm

HDMI Female to Mini HDMI Male Adapter

38.0 ( +GST 18% )
QUICK OVERVIEW
  • This Mini HDMI to HDMI adapter is capable of carrying the increased bandwidth of HDMI 2.0 at 18 Gbps.
  • It Supports Audio Return Channel (ARC), HDMI Ethernet Channel (HEC), 48 Bit Deep Color, 32 channel audio, HDCP, Dolby True HD 7.1 audio, and 3D video.
  • Also Supports resolutions up to 4Kx2K (UHD) including 4096×2160, 3840×2160, 2560×1600, 2560×1440, 1920×1200, and 1080p
  • Gold plated male to female adapter resists corrosion and provides rigidity. Grip treads help easy plugging and unplugging.

Heart Rate Pulse Sensor Module

112.0 ( +GST 18% )
QUICK OVERVIEW
  • Operating voltage: 5V
  • Operating current: 4mA
  • Pulse Sensor Board
  • 24-inch Color-Coded Cable with Standard Male Headers
  • Ear Clip for Earlobe Heart Rate Measurement
  • Velcro Finger Strap
  • Transparent Stickers to Protect Sensor

HTU21D Temperature and Humidity Sensor Module

150.0 ( +GST 18% )
QUICK OVERVIEW
  • Power supply: 1.5 ~ 3.6V.
  • Humidity measure range: 0-100%RH.
  • Temperature measure range: -40 ~ +105 °C.
  • Max. power consumption: 2.7 µW.
  • Communication: I2C.

IIC/I2C Serial Interface Adapter Module

68.0 ( +GST 18% )
QUICK OVERWIEW
  • 5V power supply.
  • Serial I2C control of LCD display using PCF8574.
  • Backlight can be enabled or disabled via a jumper on the board.
  • Contrast control via a potentiometer.
  • Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.

L293D Motor Driver Shield for Arduino

115.0 ( +GST 18% )
QUICK OVERVIEW
  • Wide supply voltage: 4.5 V to 12 V.
  • Max supply current: 600 mA per motor.
  • The driver two holes of 3 mm dia.
  • Male burg-stick connectors for supply, ground and input connection.
  • Screw terminal connectors for easy motor connection.
  • High noise immunity inputs.

Lipo Voltage Checker 1S-8S with Buzzer Alarm

106.0 ( +GST 18% )
QUICK OVERVIEW
  • Input: 1S-8S Battery
  • Battery type: Lipo/LiFe/Li-ion/LiMn
  • It has a Buzzer Alarm for low voltage indication.
  • Useful for measuring each cell voltage.
  • Cell Voltage Display Range: 0.5v-4.5v
  • Total Voltage Display Range: 3.7-36v
  • Alarm set values: Off or 2.7-3.8v